A conductor carries a current that maybe regarded as equivalent tò the sum of p components, one of them being a continuous direct current of 4.2 amp and the er a superimposed full-wave rectifier current. If the latter has a maximum value 5.4 amp, calculate the average current in the wire if (a) both components have same direction, (b) the two components are oppositely directed?

A conductor carries a current that maybe regarded as equivalent tò the sum of p components, one of them being a continuous direct current of 4.2 amp and the er a superimposed full-wave rectifier current. If the latter has a maximum value 5.4 amp, calculate the average current in the wire if (a) both components have same direction, (b) the two components are oppositely directed?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

A conductor carries a current that is equivalent to a 5-amp continuous current in one direction and a superimposed full-wave rectifier current in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?
Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
A conductor carries a current that maybe regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed half-wave rectifier current. If the latter has a maximum value of 8.3 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).
Derive the equation of the Vdc, Vrms, Efficiency, RF, and TUF of a given three-phase half-wave rectifier circuit shown. Draw the output waveform of the pulsating DC voltage neatly and accurately.
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75 µA. If the meter coil resistance is 900 Q and the multiplier resistor is 708 k2, calculate the applied rms voltmeter when the voltmeter indicates FSD.
A conductor carries a current that is equivalent to a 2.5 amp continuous current in one direction and a superimposed full-wave rectifier in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
A conductor carries a current that may be regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed full-wave rectifier current. If the latter has a maximum value of 6.4 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?