I need the answer as soon as possible A conical pivot bearing carries a load of 50KN. the angle of cone is 120°. The intensityof pressure is 45N/Cm?. The external diameter is 3 times the internal diameter. Findthe diameters of the bearing surfaces. If the power lost is 2.5kW at 140 rpm. Determinethe coefficient of friction.

Answered: À conical pivo of pressure is the…

Engineering

Mechanical Engineering

À conical pivo of pressure is the diameters the coefficient

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
A leather belt which is 125 mm wide and 6 mm thick, is used for transmitting power from a pulley. The diameter of the pulley is 750 mm and its angular speed is 500 rpm. The angle of lap is 150° and coefficient of friction is 0.3. If the mass of 1 m3 of leather is 1 kg and stress in the belt is not to exceed 2.75 MPa then find the maximum power that can be transmitted by the bel
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
Two pulleys, one 425mm diameter and the other 210mm diameter are one parallel shaft 2m apart and are connected by a crossed flat belt. Find the length of the belt required and the angle of conduct between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 200 rev/min, if the maximum permissible tension in the belt is 1 kN, and the coefficient of friction between the belt and pulley is 0.3?
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.
The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a steel gear wheel that is shrunk onto the hollow shaft has an outer radius of 150 mm. The maximum allowable tangential stress developed by shrinking the gear wheel onto the hollow shaft is 200 MPa. The length of hub parallel to the shaft axis is 200 mm, and the coefficient of static friction between the hub and the shaft is 0.40. Determine the maximum torque that may be transmitted by the gear wheel without slipping on the shaft.