A cooking pot which is cylindrical in shape with dimensions of 0.9 m in diameter and 1.2 m nigh with the outside of the pot insulation, facing ambient air, is found to be at 49 C and the air emperature is 17 C. You are required to calculate the rate of convection heat loss to ambient air from the side walls of the pot.

A cooking pot which is cylindrical in shape with dimensions of 0.9 m in diameter and 1.2 m nigh with the outside of the pot insulation, facing ambient air, is found to be at 49 C and the air emperature is 17 C. You are required to calculate the rate of convection heat loss to ambient air from the side walls of the pot.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.45P: The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system...

See similar textbooks

Similar questions

1.13 If the outer air temperature in Problem is –2°C, calculate the convection heat transfer coefficient between the outer surface of the window and the air, assuming radiation is negligible.
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
A horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.
Determine the power requirement of a soldering iron in which the tip is maintained at 400C. The tip is a cylinder 3 mm in diameter and 10 mm long. The surrounding air temperature is 20C, and the average convection heat transfer coefficient over the tip is 20W/m2K. The tip is highly polished initially, giving it a very low emittance.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
Chips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosurewhose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity ofε=0.60 and a maximum allowable temperature of Ts=85oC.(a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operatingpower of each chip? The convection coefficient may be approximated as h=11.7 W/m2K.(b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forcedconvection, with h=250 W/m2K, what is the maximum operating power?
Chips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosure whose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity of ε=0.60 and a maximum allowable temperature of Ts=85oC. (a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operating power of each chip? The convection coefficient may be approximated as h=11.7 W/m2K. (b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forced convection, with h=250 W/m2K, what is the maximum operating power
A circular grill of diameter 0.35 m and emissivity 0.7 is maintained at a constant surface temperature of 130 °C in a horizontal position. What electrical power is required when the room air and surroundings are at 24 °C?
A 0.2 m x 0.2 m vertical plate has a surface temperature that is maintained at 40°C. Air at 20°C is flowing in parallel over the plate with a velocity of 0.4 m/s. a) Do we need to consider both the forced convection and free convection? b) Calculate the increase in heat transfer rate if the forced flow assists the free convection rather than opposes it.