A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side of tank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does not roll is (for unit length) kN. 64m 1.2 m S=0.7 Water S=1 0.7 m

A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side of tank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does not roll is (for unit length) kN. 64m 1.2 m S=0.7 Water S=1 0.7 m

Name: A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side oftank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.35P: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area of the resulting body.
In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. Theweight of the gate is 4 kN and the force exerted by the stopper on the gate is measured tobe 30 kN.Draw the free body diagram of the rectangular gate.
A vessel cylindrical in shape and closed at the top and bottom is 300 mm in diameter, 1 m long and contains water up to a depth of 0.8 m. The air above the water surface is at a pressure of 60 kN/m2 . If the vessel is rotated at a speed of 250 r.p.m. about its vertical axis find the pressure head at the bottom of the vessel (i) At the centre, and (ii) At the edge
The two sides of a V-shaped water trough are hinged to each other at the bottom where they meet, as shown, making an angle of 45° with the ground from both sides. Each side is 0.75 m wide, and the two parts are held together by a cable and turnbuckle placed every 6 m along the length of the trough. Calculate the tension in each cable when the trough is filled to the rim.
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
A car plunges into a lake during an accident and lands at the bottom of the lake on its wheels. The door is 1.2 m height and 1m wide and the edge of the door is 8 m below the free surface of the water. Determine the hydrostatic force on the door and the location of the pressure centre and discuss whether the driver can open the door.
Calculate the fluid force on one side of a 5 ft by 5 ftsquare plate if the plate is at the bottom of a pool filled with waterto a depth of 8 ft anda. lying flat on its 5 ft by 5 ft face.b. resting vertically on a 5-ft edge.c. resting on a 5-ft edge and tilted at 45° to the bottom of the pool