The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 18 mm and an elastic modulus of E71 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E= 200 GPa. Assume a = 3.5 m, b -1.4 m, and c = 1.1 m. What is the magnitude of load P that is necessary to displace point A 13 mm to the left? Answer: P = i a KN

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 18 mm and an elastic modulus of E71 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E= 200 GPa. Assume a = 3.5 m, b -1.4 m, and c = 1.1 m. What is the magnitude of load P that is necessary to displace point A 13 mm to the left? Answer: P = i a KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.8P: Determine the allowable axial load Pallowfor a steel pipe column with pinned ends having an outside...

See similar textbooks

Similar questions

A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
A fixed-end column with circular cross section is acted on by compressive axial load P. The IS-ft-long-column has an outer diameter of 5 in., a thickness of 0.5 in., and is made of aluminum with a modulus of elasticity of 10,000 ksi. Find the buckling load of the column.
A fixed-pinned column is a W310 × 21 steel shape and is designed to carry an axial load of 125 kN. Determine the maximum permissible height L of the column if a factor of safety n = 2.5 is required with respect to the buckling of the column. Use E = 205 GPa and assume that the proportional limit is 340 MPa. The column may buckle about either axis of the cross section.
Determine the allowable axial load Pallowfor a steel pipe column with pinned ends having an outside diameter of 220 mm and wall thickness of 12 mm for each oft he fol lowing lengths: L =2.5 m, 5 m, 75 m, and 10 m. (Assume E = 200 GPa and y = 250 MPa.)
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A 100-mm-long rod has a diameter of 15 mm. If an axial tensile load of 100 kN is applied, determine its change in length. Assume linear elastic behavior with E = 200 GPa.
A 10-mm-diameter rod has a modulus of elasticity of E = 100GPa. If it is 4 m long and subjected to an axial tensile load of 6 kN, determine its elongation. Assume linear elastic behavior.
A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it, determine the change in its length and the change in its diameter. Assume Modulus of elasticity (E) = 2.70 GPa, and poisson's ratio (v) = 0.4. indicate free body diagram
A spreader bar is used in the assembly shown in the figure attached. It is made of a circular steel ros of diameter 32mm. Assuming that the cables and their connections are inextensible, determine largest load W that can be applied so that the spreader bar does not buckle. Both end of the spreader bar may be assumed to be pin connected. The youngs modulus of the spreader bar is, E = 200 x 10^3 N/mm^2.
Determine the maximum load P that can be applied to the structure without buckling failure.Bar AB has a square section of 8 mm on each side and bar BC has a circular section, with a radius of 6 mm. Both bars are made of steel, with a modulus of elasticity E = 200 GPa.The dimensions of the drawing are given in millimeters.
A steel pipe is fixed supported at its ends. If it is 5 m long and has an outer diameter of 50 mm and a thickness of 10 mm, determine the maximum axial load P that it can carry without buckling. Est = 200 GPa, sY = 250 MPa.
The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. Determine the smallest force P that will cause (a) only one of the wires to yield; (b) both wires to yield. Consider A-36 steel as anelastic perfectly plastic material.