A cylinder of cross-sectional area of 0.004m? contains 0.1 moles of monoatomic ideal gas. The cylinder is located verticaly and fitted with a frictionless piston of mass 10.0 kg. If the gas is at T=123 °C, what will be the height h at which the piston will be equilibrium under its own weight.

A cylinder of cross-sectional area of 0.004m? contains 0.1 moles of monoatomic ideal gas. The cylinder is located verticaly and fitted with a frictionless piston of mass 10.0 kg. If the gas is at T=123 °C, what will be the height h at which the piston will be equilibrium under its own weight.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The density of a steel anchor is 4205 kg/cu.m that is attached to a cylinder with 0.60m diameter, height of 1.2m, and with a mass of 34kg that floats in water with its axis vertical(upright). The steel anchor is attached to the cylinder which causes it to be submerged to a depth of "h" meters and remain in equilibrium position. a) Determine the equation based on the relationship between the weight of the anchor, "Wa" and the submerged depth "h". (Show step by step solution)
A balloon of spherical shape 6 m in diameter is filled with hydrogen gas at apressure of 1 bar absolute and 20°C. At a later time, the pressure of the gas is94% of its original pressure at the same temperature. What percentage of theoriginal mass must have escaped if the dimension of the balloon are notchanged?
The density of a floating object can be determined by tying just enough weight to the object to submerge it completely, and then weighing the weights and object separately in the air. Consider a wood log that weights 1600 N in air. It is found that it takes 42 kg of lead (????? = 11,300 ?? ?3 ⁄ ) to just submerge the log in the water (i.e. to achieve neutral buoyancy). For the conditions given, find thefollowing:a. The volume of the log in m3.b. The average density of the log in kg/m3For this problem, take the density of water to be ?????? = 1000 ??/ ?3.
A column arranged vertically holds a composite fluid of 18 in of mercury (SG = 13.6), 26 in of water (density = 998 kg/m^3), and 32 in of oil(SG = 0.9), with its top end exposed to the atmosphere. Calculate the pressure in psia at the bottom of the column. Knowing that fluids with higher densities sit below fluids with lower densities, illustrate the vertical column(no need to be up to scale). With solutions please.
PROBLEM 2Aluminium, due to its high strength-to-weight ratio and corrosion resistance, is a metalcritical to the aerospace industry. One can often find aluminium and its alloys as structuralcomponents of aircraft and spacecraft.An aluminium bar of 17 kg, initially at 106°??, is immersed in an open tank of 200L of liquidwater, initially at 20°??.Question:(a) Determine the final equilibrium temperature of the system made by the aluminiumbar and water ignoring heat transfer between the tank and its surroundings.
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x 10-6 m3 when filled with a liquid at a pressure p. If E = 200GN/m2 and v = 0.25, and assuming rigid end plates, determine the values of hoop stress
A hot air filled balloon of 8m diameter is used to support a platform. The surrounding airis at 20° C and 1 bar while the hot air inside the balloon is at a temperature of 70° C.Determine the buoyant force and the weight that may be supported by the balloon.
Consider a stack of six pancakes. Each pancake is made of 1/4 cup (approximately 60 mL) of batter, and the density of batter is 1 g/cm3. Consider the pancake at the bottom of the stack. What is the total weight of pancakes sitting on top of it? Express your answer in kilograms, but without entering the unit. This is not a lot of weight. Assuming that pancakes have an elastic modulus of 20 kPa, that the area of each pancake is identical (approximately 80 ), and that the stack of pancakes has a height of 55mm, compute how much the single pancake at the bottom of the stack is compressed by the weight of the pancakes on top of it. This is a very small compression, so instead you place a 4 kg weight on the pancakes. Now you see that the stack noticeably compresses. Consider the stack of pancakes as one aggregate unit with a surface area of approximately 80 cm2. What is the stress on the pancakes? Express your answer in Pascals, but without including the unit. Your observation of the normal…
In his experiment to test whether the crown of the King of Syracuse was made of pure gold or not, Archimedes immersed the crown into a container filled with water. He noted that the crown displaced 150 mL of water. If the mass of the crown is 2675 g, is it made of pure gold? A storage tank that is 15 m high is open at the top and initially filled with water. It developed a hole 12 m below the surface of water along its side. (a) What is the initial speed of water through the hole? (b) How far from the base of the tank will the water stream strike the ground?
In celebration of the end of term, see the symmetric wine glass of 300 g mass, as shown below.Note that the wine is frozen because you left the glass outside. What is the maximum force magnitude P that can be applied to the glass before movement occurs? What kind of movement will occur? What kind of movement will occur if the base is changed to be 120 mm wide, themass of the glass increases to become 400 g, and μs = 0.2?
An asphalt concrete specimen has a mass in air of 1327.8 g, mass in waterof 792.4 g, and saturated surface-dry mass of 1342.2 g. Calculate the bulkspecific gravity of the specimen
A tall open-topped standpipe has an inside diameter of 2,750 mm and a wall thickness of 6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3 . (a) What height h of water will produce a circumferential stress of 16 MPa in the wall of the standpipe? (b) What is the longitudinal stress in the wall of the standpipe due to the water pressure?