A diode has forward characteristics as follows: Table 1 V (V) | I (A) 0.50 0.75 1.00 1.25 1.50 1.75 2.00 0.1 1.5 2.3 3.3 5.0 6.7 8.5 (a) The diode is connected in series with a 1.0 Q resistor across a voltage supply of peak value of 10V. What is the peak value of diode forward current? (b) What if the same circuit now change to limit the peak current to 5.0OA, what is the value of the resistor? Design and sketch your circuit.

A diode has forward characteristics as follows: Table 1 V (V) | I (A) 0.50 0.75 1.00 1.25 1.50 1.75 2.00 0.1 1.5 2.3 3.3 5.0 6.7 8.5 (a) The diode is connected in series with a 1.0 Q resistor across a voltage supply of peak value of 10V. What is the peak value of diode forward current? (b) What if the same circuit now change to limit the peak current to 5.0OA, what is the value of the resistor? Design and sketch your circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
A 1N4748A zener diode has a ZZ of 23 Ω. Taking the data from the datasheet VZ = 22 V with a test current, IZ, of 11.5 mA. What is the voltage across the zener terminals when the current is 6 mA? When the current is 20 mA? Make the representation of the values by means of their curve characteristic.
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Find the value of dc and ac resistance of a Germanium junction diode if the temperature is 25 degree Celcius, Reverse Saturation Current is 20 microAmperes and applied voltage of 0.1V. a.) rDC= 75.6 ohms, rAC=11.2 ohms b.) rDC= 120.7 ohms, rAC= 28.4 ohms c.) rDC= 95.1 ohms, rAC=12.3 ohms d.) rDC= 109.2 ohms, rAC=26.3 ohms
(I) Determine the average ac resistance for the diode of the Figure below for the region between 0.6 V and 0.9 V. (II) Then determine the ac resistance for the diode of the Figure below at 0.75 V and compare it to the average ac resistance obtained in (I).
A 1N4728 zener diode has a Zz of 10 ohms. Considering the data from the manufacturer's sheet, Vz = 3.3 V with a test current, Iz, of 76 mA. What is the voltage across the zener terminals when the current is 95 mA? When the current is 55 mA? Include the graph where these values are shown.
Draw the V-I characteristic curve of a Ge based Zener diode with Zener breakdown voltage (?z=5 ?). Indicate three different regions of the curve. Subject: Electronic devices
Find the value of dc and ac resistance of a Germanium junction diode if the temperature is 25 degree Celcius, Reverse Saturation Current is 20 microAmperes and applied voltage of 0.1V.
3. It is required to design a full-wave rectifier circuit using the circuit shown below to provide an average output vol tage of10 V. find the required turns ratio of the transformer. Assume that a conducting diode has a voltage drop of0.7 V. The ac line vol tage is120 Vrms.