A diode will behave as an open circuit if the voltage in the circuit is less than __________ a) cut off voltage b) saturation voltage c) leakage voltage d) threshold voltage
Q: 1. Zener and Avalanche breakdown 2. Define PIV of a Diode. 3. Determine the dc resistance of a diode…
A: In this question we will find unknown currents .....
Q: In an unbiased p-n junction, holes diffuse from the p-region to n-region because A- free electrons…
A: Question 1: in an unbiased p-n junction, hole diffuse from the P region to n region because ..…
Q: (b) The governing equation for the diode is: (A) ) Define the parameters within this equation. (i)…
A:
Q: For the ideal-diode clipper circuit given below, VS = 12.sinωt V. Determine the output voltage Vout…
A: 1) Voltage at x or y determines the operation of diodes. For the diode D2 to be operated in Forward…
Q: (c) Forward biasing indicates the application of a voltage across a diode that enables current to…
A: The answer is
Q: A silicon diode said to be a 1-mA device displays a forward voltage of 0.7 V at a current of 1 mA.…
A: The conductivity of semiconductor is lies in between conductor and insulator. The conduction in…
Q: (a) Find the worst-case values of the Q-point current for the diode shown using the ideal diode…
A: (a) Draw the circuit, when the diode is forward biased, and the resistors with the added values of…
Q: A diode has 1 mA at 0.6 V and 120 mA at 0.8 V. Find a piecewise model (battery+resistor) for that…
A: Given: A diode has 1 mA at 0.6 V and 120 mA at 0.8 V. To find: The piecewise (battery+resistance)…
Q: A diode is tested at the presence of dc+ac source, where the diode's average current level (dc…
A:
Q: You are asked to design a Zener diode voltage regulator, as shown in Figure 1.e, to have a…
A:
Q: In the given circuit, (diodes will be considered ideal. a) Draw the V0 output by calculating it…
A:
Q: 1. Given a theoretical solar cell with open circuit (no load) output voltage of 0.55V and ideal…
A: Given The ideal diode current Io=2×10-11 A The open-circuit output voltage Voc=0.55 V (a) At no-load…
Q: 1- Use your results to Plot the characteristics of the diode in both, forward and reverse biasing…
A: 1. diode is a linear or non linear device 2. electric field across PN junction 3. can a diode be…
Q: Consider the following rectifier circuit with four ideal diodes and an ideal Thyristor. (a) Sketch a…
A: Given Circuit:
Q: MCQ
A:
Q: For the ideal-diode clipper circuit given below, VS = 12.sinωt V. Determine the output voltage Vout…
A:
Q: For the diode parameters given below = 1015atoms/cm³, Np = 1017atoms/cm³, A = 0.025cm², T = 300K, D,…
A: The Answer is
Q: 4. Give at least two examples of semiconductor materials which are used for LED. 5. Develop the…
A:
Q: potential, the diode current is large, which * In a PN junction when the applied voltage overcomes…
A: If the applied voltage (VD) Barrier voltage (uv)the diode becomes ON ans current will flow inlarge…
Q: For the following circuit, consider that both diodes Di and Dz are ideal, that is Vx = 0 V. Consider…
A: Analog electronics
Q: Given a Zener diode where Vz = 5 V at Izr = 25 mA, Zz = 5 N, Izm = 150 mA, Izx = 1 mA, and R= 250 2.…
A:
Q: For the following circuit, consider that both diodes D1 and D2 are ideal, that is VK = 0 v. Consider…
A: Analog electronics
Q: R1 Vx - Considering the given circuit, Vz = 6.5 V @ 4 mA, R1 = 0.5 kN, V = 12±3 V, and rz 25 N. If…
A: The minimum value of zener diode in breakdown region, if the voltage are given.
Q: An electronic device with a pn junction is used to make a computer. If the speed of the computer…
A: Given A pn junction device which runs a computer,we need to suggest changes so that it will work…
Q: Consider the circuit shown below. A string of four identical diodes is used so that Vo = 2.8V when…
A:
Q: Homework # 1: The manufacturer of a selected diode gives the rate of fall of the diode current di/dt…
A: As per our guidelines we are supposed to answer?️ only one question. Kindly repost other questions…
Q: The proposed circuit on the right illustrates a simple voltage threshold detector, where D1 is a red…
A: KIRCHHOFF’S LAW KCL: The algebraic sum of all currents at a node is zero. KCL is…
Q: 1. Zener and Avalanche breakdown 2. Define PIV of a Diode. 3. Determine the dc resistance of a diode…
A: Zener Breakdown: It is due to thermal ionisation of electrons in the depletion region. Avalanche…
Q: 1. Zener and Avalanche breakdown 2. Define PIV of a Diode. 3. Determine the dc resistance of a diode…
A: In this question we will solve average current , RMS current , ripple factor ,output input power ,…
Q: N Junction A You apply a voltage to the PN junction to a circuit as above. Note that the saturation…
A:
Q: In your own words and with the aid of suitable diagrams, describe the following: a) Formation of the…
A: Depletion region It is the region where the charge is zero because the mobile charge carriers are…
Q: The half-controlled single-phase bridge circuit shown in : below is supplied at 120 V. Neglecting…
A:
Q: Homework # 1: The manufacturer of a selected diode gives the rate of fall of the diode current di/dt…
A: In this question 1 , reverse recovery time is given and rate of fall of diode current is given..We…
Q: Using one NPN transistor, one PNP transistor, one general purpose diode, one LED and two resistors,…
A: According to the question, Here is the circuit diagram that consist one npn transistor and one pnp…
Q: Consider the circuit below containing two identical, p-n junction diodes D₁ and D₂: 2 ks2 www 5 V-…
A: Given, Threshold voltage VT=0.7V Ambient temperature=300K Reverse saturation current= IS=5μA Here,…
Q: For the circuit shown below at tėmperature 35°! Which diode will operate first? Why? Calculate-V1…
A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.
Q: 5x10 cm and Na The doping concentrations of p-n junction are N. 1.5x10 cm, and the minority carrier…
A: "According to the Company's policy we will solve only the first three sub-parts of the question".…
Q: A semiconductor junction diode, we can say that: a) The diode is composed of two types of crystal,…
A: I am giving the points which illustrate the correct answer.
Q: Provide two designs of shunt regulators utilizing the 1N5235 zener diode, which is specified as…
A: Given Data" VZ = 6.8V rz = 5ohm IZ = 20mA; IZ = 0.25mA (nearer the knee), rz = 750ohm
Q: a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at…
A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…
Q: Using diode equation, find the p-n junction Germanium diode current for a forward bias of 0.2 V at…
A:
Q: Consider the diode circuit shown in the figure, where R, = R2 = 1 kN. R1 o V. Vs(t) Ip R2 VB /hen VB…
A:
Q: A diode has 3 nmA at 0.6 V and 210 mA at 0.75 V. Find its reverse saturation current (Is) and…
A: From the equation of diode current here we can calculate the ideality factor and reverse saturation…
Q: . Consider the diode circuit shown in the figure, where R1 = R2 = 1 kN. v. v.(t) When V3 = 4 V and…
A:
Q: In PN junction in series with a 100 ohms resistor, is forwarded biased. So that a current of 100 mA…
A: Circuit diagram is given as, In first case diode is forward bias replacing the diode as short…
Q: 1) Consider the circuit at right, consisting of two R LEDS (one red, one green), which you can model…
A:
Q: 1.) Consider the following voltage regulation circuit employing three diodes in series, assuming the…
A: According to the question we have to (a) Nominal output voltage vo with no load; (b) Line…
Q: Using one NPN transistor, one PNP transistor, one general purpose diode, one LED and two resistors,…
A: The required diagram is shown in the below figure:
Q: For a metallurgical junction doping given below, sketch the expected charge density, electric field,…
A: Need to find graphs of voltage electric field and charge density
mcq
. A diode will behave as an open circuit if the voltage in the circuit is less than __________
a) cut off voltage
b) saturation voltage
c) leakage voltage
d) threshold voltage
------------------------------
At room temperature (VT = 26) what will be the approximate value of r when n=1 and I=100mA?
a) 0.26 ohms b) 2.6 ohms c) 26 ohms d) 100 ohms
Step by step
Solved in 2 steps with 2 images
- The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)MCQ 1 . A diode will behave as an open circuit if the voltage in the circuit is less than __________ a) cut off voltage b) saturation voltage c) leakage voltage d) threshold voltage ----------------------- 2 . In the diode volt ampere characteristics what will be the resistance if a slope is drawn between the voltages 50 to 100 and corresponding current 5 to 10? a) 5 ohms b) 10 ohms c) 50 ohms d) 100 ohms ---------------------- 3 Diodes can be used in the making of a) Rectifiers b) LED lamps c) Logic gates d) All of the mentioned
- Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at 65 mA and ZZ = 23 Ω. What is the Zener voltage at 70o C, if it has a positive TC of 0.08 %/oC.? b) Using a Complete diode model, find the diode current (ID), diode voltage (VD), and output voltage (Vo) for the diode circuit shown below. Given that: Vs = 20 V, RL=3 kΩ , Barrier Potential VF = 0.3 V , and r’d = 70 Ω. If the diode was reversed and IR = 200 µA, Determine the diode reverse voltage (VR)Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
- A shunt regulator employs a zener diode for which VZ = 10.1 V at IZ = 10 mA while VZ = 10.2 Vat IZ = 20 mA. The available supply voltage (VS) is 15.0 V, R = 300 ohm, and the load resistance(RL) =1.0 kohma) Find VZ0 and rz.b) Calculate the output voltage (VO).c) Determine the line regulation (ΔVO/ΔVS).d) Using the line regulation obtained in (c), determine the values of the output voltage (VO) if thesupply voltage (VS) is increased from 15 V to 15.1 V.In PN junction in series with a 100 ohms resistor, is forwarded biased. So that a current of 100 mA flows. If the voltage across this combination is instantaneously reversed at t = 0 current through diode is approximately given by:A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
- Briefly discuss the difference between Diode Piecewise-linear model, Simplified model, and Ideal device/ equivalent circuit. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each. Discuss briefly how to test junction diode.1. Briefly discuss the difference between Piecewise-linear model, Simplified model, and Ideal device. 2. Discuss briefly how to test junction diode. 3. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each.A 0.5 W zener diode is rated to have VzT = 4 V at a test current of IzT =11.0 mA. Its incremental resistance r, = 68.0 Ohms. What voltage will result when conducting a reverse current of Iz = 21 mA? What is the maximum safe current, using the linearized model and including the effect of rz?