A driveshaft for a milling machine transmits15.0 hp at a speed of 240 rpm. Compute the tor-sional shear stress in the shaft if it is solid with adiameter of 1.44 in. Would the shaft be safe if thetorque is applied with shock and it is made fromSAE 4140 OQT 1300 steel?447.

Power transmitted by the driveshaft P : 15.0 hp The speed of the driveshaft N = 240 rpm The diameter…

Answered: A driveshaft for a milling machine…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Write legibly, provide manual step by step solution, and diagram for below given problem. The shaft whose torque varies from 3000 to 8000 in-lb has 2 inches in diameter and 60 000 psi yield strength. Compute for the shaft mean average stress. (Ans. F=3501.41psi)
A hollow shaft has an inner diameter of 0.035 m and an outerdiameter of 0.06 m. Compute for the torque if the shear stress isnot to exceed 120 MPa in Nm.
A shaft is transmitting 100 kW at 160 rpm. Find a suitable diameter for the shaft if the maximum torque transmitted exceed the mean by 25%. Take maximum allowable shear stress as 70 MPa.
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
Two designs for shaft are being considered. Both have an outside diameter of 60 mm and are 500 mm long. One is solid but the other is hallow with an inside diameter of 40 mm, both are made from steel ( G=80 GPa). Compare the torsional shear stress, and the mass of the two designs if they are subjected to a torque of 71 N.m.
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the maximum shear stress in the shaft
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A driveshaft for a milling machine transmits 15.0 hp at a speed of 240 rpm. Compute the tor- sional shear stress in the shaft if it is solid with a diameter of 1.44 in. Would the shaft be safe if the torque is applied with shock and it is made from SAE 4140 OQT 1300 steel? 447.