Consider the 1inch steel square tube loaded in torsion.the tube has wall thickness of 0.0196 inch and length is 40 inches and maximum allowable shear stress is 7.2 kpsi determine maximum torque that could be applied and corresponding angle of the twist.

Consider the 1inch steel square tube loaded in torsion.the tube has wall thickness of 0.0196 inch and length is 40 inches and maximum allowable shear stress is 7.2 kpsi determine maximum torque that could be applied and corresponding angle of the twist.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Related questions

Q: A steel tube with the cross section shown is 6 ft long and has a wall thickness of 0.12 in.…

Q: The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at…

A: Given data as per question Diameter of shaft =2.5 in Length of shaft =2 in Torque applied =750 lb.in…

Q: Consider the compound shaft KDQC which is composed of a 300 mm long solid rod DQC (G = 35 GPa)…

A: Since we only solve three subparts at once, we will solve the first three. Please share the question…

Q: A compound steel [G = 80 GPa] shaft consists of solid 30-mm-diameter segments (1) and (3) and tube…

A: Given data:

Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…

Q: The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The…

A: Given data: P=200 hpN=3500 rpmG=12×106 psiτ=12000 psi Need to determine the diameter of the smallest…

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

Q: 9. A torsion tube is made from aluminium tube having an outside diameter of 60mm and a wall…

A: Given: The outside diameter of the tube, D = 60 mm The wall thickness of tube, t = 5 mm The young…

Q: Problem 3. A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the…

Q: Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and…

A: Given data: T=50 kN.m Need to determine the angle of twist, at point C, maximum shear stress,…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

Q: A 5 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 180 HP. The shaft…

A: Given: Length of the shaft (L)=5ft Power (P)=180HP Shaft speed (N)=3000rpm or 2π×300060=314.159rad/s…

Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…

Q: : Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length…

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

Q: A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, the…

A: Given data: d=50 mm=0.05 mL=500 mm=0.5 mT=1100 N.mθ=0.6°=0.010472 rad Need to determine the maximum…

Q: Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and…

A: Given data:

Q: A 2000 in-Ibf torque acts on a hollow shaft with an outer diameter of 2 in and an inner diameter of…

A: Torque, T=2000 in.lbfOuter diameter of shaft, do=2 inInner diameter of shaft, di=1.75 in

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

Q: A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, the…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: a solid rod with a circular cross-secton is subject to a torque of 253 N.m. if diameter of the rod…

Q: A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the…

Q: The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power…

Q: The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm.…

Q: • The shaft whose torque varies from 2000in-lb to 6000in-lb has 1.5" diameter and a yield strength…

A: To find: The shaft's mean stress. Given: The maximum torque is Tmax=6000 lb‐in. The minimum torque…

Q: A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter,…

Q: Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb =…

A: Shear stress is defined as the intensity of force acting on the cross sectional area. Shear stress…

Q: 3.30 A solid steel shaft transmits 20 hp while running at 120 rev/min. Find the smallest safe…

Q: 1. The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by…

A: given data D=150mmSy=420Mpaθ=20°SUT=560MpaTA=340NmFOS=2.5(A) Consider the equation of torque acting…

Q: Q.4) A composite shaft is subjected to two torques as shown below. Shaft ABC is a hollow…

Q: An aluminium hollow thin-wall torsion member shown in Fig. 3.15 is 3 m long. If a torque of 10 kN-m…

A: We know that a 3 m long aluminium hollow thin wall torison member is illustrated in the diagram.We…

Q: Consider the compound shaft KDQC which is composed of a 300 mm long solid rod DQC (G = 35 GPa)…

A: Write the given data in the problem. Grod=35 GPaGpipe=63 GPa d=170 mm D=210 mm Here,…

Q: Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length of…

Q: A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a…

Q: hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate…

Q: A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key…

A: GivenT=912.4Nmd=63.5mmt=15.875mmw=11.1125mmτ=61.2MPaσ=98.8MPa

Q: Task 4: A solid steel shaft in a rolling mill transmits 20 KW of power at 2 Hz. Determine the…

A: The steel shaft of the rolling mill transmits 20KW at 2 Hz, The torque in the shaft while…

Q: a) Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected…

Q: A SOLID circular shaft transmits 50 horsepower while operating at a rate of 150 rev/min. If the…

Q: solid steel shaft must not twist through more than 3° in a 6-m length when subjected to a torque of…

Q: The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa.…

Q: T 100 mm 70 mm 70 mm 1.5 m 2 m T

Q: n 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to a…

A: Given: The overall length, L = 6.5 m The shear modulus, G = 81 GPa Teh diameter of shaft, d = 66 mm…

Q: the Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the…

A: Write the expression of angle of twist.

Q: a 101.6 mm shaft using a flat key, whose width is 25.4 mm, is transmitting a torque of 63,000 in-lb.…

A: Diameter of the shaft, d= 101.6 mm Width, b= 25.4 mm Torque, T= 63000 in.lb= 63000(25.4) mm.lb=…

Q: A square steel bar, 25 mm on a side and 650 mm long, is subjected to a torque of 230 N #m. Compute…

Q: 6. A marine turbine developing 15,000 hp and it turns the shaft at 300 rpm. The propeller which is…

Q: A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the…

A: Schematic diagram of flanged shaft after considering the force F in the bo;t due to torque T

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

Q: A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not…

A: Given that, for a hollow shaft, L = 2540 mm T = 4 kN-m Maximum angle of twist = 3 degrees Maximum…

Q: Detailed solution would be appreciated thanks!!. The steel shaft is formed by attaching a hollow…

Q: A shaft shown in the fig consist of 3-in diameter aluminum segment and 2 in diameter steel segment…

A: Given data: T=10000 lb-in Need to determine the torque in steel (Tst) in terms of torque in aluminum…

Q: A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75…

A: Given dataPower transmitting capacity of the shaft P = 8hpRotation of the shaft N = 2250 rpmDiameter…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Data given- d = 100 mm T = 10 × 103 N-m = 10 × 106 N- mm Axial stress = 50 MPa

Q: A circular-closed-tube shaft, with an outer radius of 20 mm and an inner radius of 15 mm, and 650 mm…

Q: A hollow steel propeller shaft, 18 ft long with 14-in. outer diameter and 10-in. inner diameter,…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The shaft is to be designed to safely transmit 200 hp at 3500 rev/ min. Determine the diameter of the smallest shaft that can be used and its corresponding angle of twist. For the steel, use a working shear stress of 12 000 psi and G = 12 x 106 psifind, a) diameter b) angle of twist
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner diameter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel
An elevator torque tube is made of 24S-T aluminum alloy & has dimensions of 2- by 0.083 in. Find the angle of twist if the torsional shearing stress has a value of 10,000 psi for a length of 80 in.
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner dieter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel. complete solution
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you