A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion-energy and maximum-shear-stress theories, analyze the following plane stress states/principal stresses. - 12 kpsi, ơy = 15 kpsi, 7,y = -9 kpsi -24 kpsi, Txy (d) 0, = %3D %3D (e) o, = -24 kpsi, ơ, = -24 kpsi, 7y = -15 kpsi %3D = 30 kpsi OA = 30 kpsi, O = 30 kpsi, ơB = %3D (g) = -30 kpsi

A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion-energy and maximum-shear-stress theories, analyze the following plane stress states/principal stresses. - 12 kpsi, ơy = 15 kpsi, 7,y = -9 kpsi -24 kpsi, Txy (d) 0, = %3D %3D (e) o, = -24 kpsi, ơ, = -24 kpsi, 7y = -15 kpsi %3D = 30 kpsi OA = 30 kpsi, O = 30 kpsi, ơB = %3D (g) = -30 kpsi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Why do we define engineering and true stresses for tension/compression loading but not for shear loading?
The assembly shown consists of an aluminum shell (Ea = 70 GPa, αa = 23.6 × 10−6/°C) fully bonded to a steel core (Es = 200 GPa, αs = 11.7 × 10−6/°C) and the assembly is unstressed at a temperature of 20°C. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 185°C. The stress in the aluminum is − _____ MPa.
1. A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw all 3 Mohr's circles, find the principal stresses, and calculate the safety factor against yield using both the distortion-energy (von Mises) and maximum shear stress (Tresca) criterions. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?
Question 1: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the maximum axial force (P) that can be applied. d=100mma) On the theory of maximum normal stressb) Maximum shear stress theoryc) Calculate according to the maximum strain energy theory.The structure is made of steel and the proportional limit is 250 MN / m2 in pressing and drawing, and 140 MN / m2 in shear. The elasticity module of the material is 200 GPa and the Poisson's ratio is 0.3. d=100mm
A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90⁰ with respect to the other end without exceeding an allowable shear stress of 300 MPa?
A rectangular steel block is 76 mm long in the x direction, 50 mm long in the y direction, and 100 mmlong in the z direction. The block is subjected to a triaxial loading consisting of three axial forces asfollows: 214 kN tension in the x direction, 268 kN compression in the y direction, and 241 kN tensionin the z direction. If v = 0.30 and E = 200 GPa, determine the axial load in the x direction that wouldproduce the same deformation in the y direction as the original loading.
6 cans containing soda made out of aluminum ( E = 69 GPa, σY = 240 MPa ) material are shaken. Shaking them creates an internal pressure of 0.14 MPa in each can. A uniform load of W is applied to the cans through a plate which has a negligible weight. The inner diameter of each can is 2R = 62 mm, the wall thickness is t = 0.25 mm and the length is L = 112 mm. According to the von - Mises yield criterion, determine the maximum magnitude of the applied load W. Note: The weight of the cans will be neglected in calculations. Accept that the liquid in the cans does not provide any support to the cans and no buckling occurs in the cans.
What happens when the in-plane principal stresses are of opposite signs?
An ASTM cast iron has minimum ultimate strengths of 32 kpsi in tension and 95 kpsi in compression. Find the factors of safety using Coulomb Fragile Mohr (CMF) and Modified Mohr (MM) theories for the following stress state. σx = −3 kpsi, σy = −9 kpsi, τx y = −4 kpsi
A steel with a yield stress of 300 MPa is tested under a state of stress whereσ2 = σ1/2 and σ3 = 0. What is the stress at which yielding occurs if it isassumed that:(a) The maximum-normal-stress criterion holds?(b) The maximum-shear-stress criterion holds?(c) The distortion-energy criterion holds?
A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and trunk onto a steel will 800.50 mm in diameter. The modulus of elasticity of steel is 200 GPa. 1) Which of the following most nearly gives the tensile stress in the tire. a. 145 MPa b. 130 MPa c. 110 MPa d. 125 MPa 2) Which of the following most nearly gives the compressive pressure between the tire and the wheel. a.) 4.35 MPa b.) 3.30 MPa c.) 3.90 MPa d.) 3.75 MPa 3) If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, which of the following most nearly gives its thickness. a.) 4.84 mm b.) 2.42 mm c.) 2.58 mm d.) 5. 16 mm
What are principal stresses?