i need the answer quickly Q1) A steel bolt, 2.5 cm in diameter, carries atensile load of 40 kN. Estimate the average tensilestress at the section o and at the screwed section2.1Don danterb, where the diameter at the root of the thread is2.50omdareter2.1 cm?

Answered: Image /qna-images/answer/fbce6272-f878-4276-a828-fcd396eb53bc.jpg

Answered: Q1) A steel bolt, 2.5 cm in diameter,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel cable with a diameter of 3.0cm supports a load of 2.0 kN. What is the frictional length increase of the cable compared with the length when there is no load if Y= 200 GPa?
PLS ANSWER IN 20MINS IF POSSIBLE. THANK YOU The five-bolt connection shown in the figure must support an applied load of P = 295 kN. If the average shear stress in the bolts must be limited to 120 MPa, determine the minimum bolt diameter that may be used for this connection.
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
A brass link (Eb=105 GPa, αb=20.9 3 10–6/°C) and a steel rod (Es= 200 GPa, αs=11.7 3 10–6/°C) have the dimensions shown at a temperature of 20°C. The steel rod is cooled until it fits freely into the link. The temperature of the whole assembly is then raised to 45°C. Determine (a) the final normal stress in the steel rod, (b) the final length of the steel rod
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?
A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter equal to 5.79mm. If the resisting torque supplied by the table is equal to 0.36 N.m, what is the maximum shear stress of the drill bit? If the allowable shear stress in the drill bit is 44.215MPa, what is the maximum resisting toque before the drill binds up?
A circular dise of 150 min diameter and 10 mm thickness is compressed between two flat dies, and μ = 0.1 determine sticking radius and load on dies if avg. yield stress is 200 N/mm².
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall., Determine the magnitude of the stress in a fiber 50 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
Find the max shear stress in given data of two circular shafts (S) AND (H)
A circular rod is stretched by a force of 3kN. Solve the diameter of the rod if the stress is not to exceed 153MPa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q1) A steel bolt, 2.5 cm in diameter, carries a tensile load of 40 kN. Estimate the average tensile stress at the section a and at the screwed section 2.1Don danter b, where the diameter at the root of the thread is 250am dareter 2.1 cm?