A dumbbell is at rest on a frictionless horizontaltable. The, dumbbell consists of two pointlikeparticles each of mass m = 4 kg at the ends ofa massless rod of length l776m. A pointlikeparticle, also of mass m = 4 kg, moves at speedv = 24 m/s perpendicular to the dumbbell asshown in the figure. The moving particle collidesand sticks to the upper mass of the dumbbell.%3D(top view)What is the angular speed around the center of mass of the resultingsystem after the collision?

Mass of particle 1=Mass of particle 2=m=4 kg lenght of particle 1=0lenght of particle 2=l=6 m…

Answered: A dumbbell is at rest on a frictionless…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block. NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the figure. if the left propeller starts from rest, w1=0 and the right propeller starts with an angular velocity that the right propeller ends up with after both propellers have collided.
A counterweight of mass m= 4.10 kg is attached to a light cord that is wound around a pulley as shown in the figure below. The pulley is a thin hoop of radius R = 6.00 cm and mass M = 2.30 kg. The spokes have negligible mass. What is the net torque on the system about the axle of the pulley? When the counterweight has a speed v, the pulley has an angular speed ? = v/R. Determine the magnitude of the total angular momentum of the system about the axle of the pulley. Using your result from (b) and τ = (dL) / (dt), calculate the acceleration of the counterweight. (Enter the magnitude of the acceleration.)
A highway curve with a radius of 120 m is banked so thatthere is no lateral pressure on the wheels of a car at aspeed of 48 kph. A car weighing 17.8 kN with 1.5-mdistance between its wheels and height h = 0.70 m travelsaround the curve at 96 kph. (a) What is the normal forceon the car’s outer wheels? (b) If friction is great enough toprevent skidding, at what speed would overturningimpend?
Block A (m = 5 kg), seen in the figure, sits on a smooth surface and is attached by a slender rod to a ball-and-socket joint at B. If the moment and force shown are simultaneously applied to the block, what will the speed of the block be after 4 seconds (starting from rest)?
A disk and a ring both homogeneous with masses M1=0.94 kg and M2=M1/6 and radii R1=0.36 m and R2=R1/2, respectively, are coupled by an ideal C strap, as shown in the figure below . At a given moment, a work of modulus W=35 J is performed on the system that, starting from rest, makes the disk and the ring rotate around their symmetry axes. In view of this, answer: what is the value of the linear velocity v at the edge of the disk? Consider that the strap does not slide over the edge of objects. Choose one: Escolha uma: a. 14,80 m/s b. 12,68 m/s c. 10,57 m/s d. None of the other alternatives e. 19,02 m/s f. 16,91 m/s g. 8,46 m/s h. 6,34 m/s
A 0.50-kg trash-can lid is suspended against gravity by tennisballs thrown vertically upward at it. How many tennis ballsper second must rebound from the lid elastically, assumingthey have a mass of 0.060 kg and are thrown at 15m/s
Block A with a weight of 100N (mA=10kg) moves to the right (vA=1 m/s) at the moment shown in the figure. Since the kinetic friction coefficient between the surface and block A is μk=0.2, find the speed of block B when it moves 2 meters its weight is 200N (mB=20kg)
A prop shaft of a heavy duty truck has two bearings which are positioned at 3 meters from each other. The shaft must rotate 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of 10 kg and 5 kg acting at the extremities of the arms 0,45 m and 0,6 m long, respectively. The planes in which these masses rotates are 1,2 m and 2,4 m, respectively, from the left end bearing supporting the shaft. The angle between the arms is 60 degrees. If the masses are balanced by two counter-masses named X and Y rotating with the shaft acting at a radius of 0,3 m and placed at 0,3 m from each bearing centre. 1.Draw a diagram illustrating the position of masses on the shaft. 2.Calculate the dynamic force in Newtons 3.Calculate the moment acting on the shaft in Newton-metre.
The figure depicts two pucks on a frictionless table. Puck 2 is four times as massive as puck 1. Starting from rest, the pucks are pushed by two equal forces. 1-Which pucks will have the grater kinetic energy upon reaching the finish line? 2- Which puck will reach the finish time first ?
Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the figure. If the left propeller starts from rest, w1=0 and the right propeller starts with an angular velocity equal to w2, find the angular velocity with which the right propeller ends up after both propellers have collided.
A team of jubliant engineering students, celebrating winning a designcompetition, fires their potato gun straight up into the air. (a) Assuming a quadratic airdrag on the potato with magnitude F (v) = mkv^2, and taking +y to be the upward direction,show that the potato speed varies with height above the ground according to the equations:

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS