A EI kNm kNm kNm 3 m 1 B 3 EI q kN/m 2EI 6 m C 4 m Click to see additional instructions Using cross method, determine the distribution factors for cross method (DF₁, DF₂, DFg and DF4) and internal bending moment at sections 1, 2, 3 and 4 (M₁, M₂, Mg and M4) in the frame? q 40 kN/m (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!! For end moments, define correct sign according to sign convention in DIAGRAMS!!) (Use "dot" for decimals and submit your answer with 2 digits) DF, = DF₂= DFg DF M₁ M₂= M₂ =

A EI kNm kNm kNm 3 m 1 B 3 EI q kN/m 2EI 6 m C 4 m Click to see additional instructions Using cross method, determine the distribution factors for cross method (DF₁, DF₂, DFg and DF4) and internal bending moment at sections 1, 2, 3 and 4 (M₁, M₂, Mg and M4) in the frame? q 40 kN/m (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!! For end moments, define correct sign according to sign convention in DIAGRAMS!!) (Use "dot" for decimals and submit your answer with 2 digits) DF, = DF₂= DFg DF M₁ M₂= M₂ =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 6m simply supported beam AB carries 2 concentrated downward loads of P=48KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the first constant of integration, C1? Express your answer in KN-m2 in 2 decimal places.
NEED ASAP, thank you! Using SLOPE DEFLECTION METHOD for the continuous beam below, determine the following structural parameters and support moments using unreduced rotational stiffness; 1. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member AB in kN-m, FEMBA 2. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member BC in kN-m, FEMBC 3. The value that most nearly gives the absolute value of the Moment at A in kN-m 4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA
Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
W= 1317 kN/mUsing Slope Deflection Method, determine all reactions at supports also, determine shear andbending moments with complete labels. Use |=1/12 bh^3 and E = 2.15x10^7 KPa
For the section, Iz = 31.7(10−6) m4, Iy = 114(10−6) m4, Iyz = −15.8(10−6) m4. Using the techniques outlined in Appendix A, the member’s cross-sectional area has principal moments of inertia of Iz = 28.8(10−6) m4 and Iy = 117(10−6) m4, calculated about the principal axes of inertia y and z,respectively. If the section is subjected to the moment M = 15 kN # m, determine the stress at point A using Eq.
A simply supported beam having a span of 8m, carries a concentrated load of 40kn at 6m. from the left support. Use EI=80000 kN-m^2.using conjugate beam method1. Compute the slope at the left support.a. 0.00125 radb. 0.001 radc. 0.00727 radd. 0.00025 rad2. Compute the slope at a point 2m. from the left support. a. 0.00125 radb. 0.001 radc. 0.00727 radd. 0.00025 rad3. Compute the deflection at the point of application of the loads. a. 3mmb. 0.72mmc. 6.16mmd. 5mm
Based on the box beam geometry below, determine the slenderness ratio for the web λweb,Btf = 480mm, thickness of top flange = 16mmBbf = 220mm, thickness of bottom flange = 20mm d1 = 550mm, web thickness = 12mm.Assume all plates have fy = 300MPa, and that the box beam has one vertical line of symmetry
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
Using Double Integration Method determine the following: Reaction at propped support and Wall moment. Use E=15GPa and I=50x10⁶mm⁴.
PLS ANSWER ASAP. I'LL RATE , THANKSUsing SDM for the frame shown below, determine the following structural parameters, FEM and support moments; Determine the ff. 1. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint A of member AB in kN-m, FEMAB 2. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint C of member BC in kN-m, FEMCB 3. The value that most nearly gives the absolute value of the Moment at C in kN-m 4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA
A singly reinforced beam that is 200 mm wide and effective depth of 350 mm is reinforced with 2 – 16 mm diameter steel bars. fc'= 24 MPa; Fy = 275 MPa. 1. Find the depth of rectangular stress block a. 27.10 b. 24.39 c. 29.81 d. 23.04 2. Find the ultimate moment capacity of the reinforced concrete beam section shown in kN-m if fc’ =24 MPa and fy = 275MPa. a. 36.83 kNm b. 28.46 kNm c. 33.49 kNm d. 40.18 kNm 3. Find the maximum total ultimate distributed load that the said beam could carry on a simple span of 3 m a. 32.74 kN/m b. 25.30 kN/m c. 35.72 kN/m d. 29.76 kN/m
PLS ANSWER ASAP Determine the resultant reaction in D in kN using slope deflection method or moment distribution method. The loads are P = 60kN, w = 20kN / m and M = 35kNm Use E = 200GPa and I = 300 * 10 ^ 6 mm ^ 4 . Input the magnitude only.