P2.3. Consider the floor plan shown in Figure P2.3. Com- pute the tributary areas for (a) floor beam B1, (b) floor beam B2, (c) girder G1, (d) girder G2, (e) corner column C1, and (f) interior column C2. (A) (B C I B2 I G3 I (2) 6 @ 6.67' = 404 I HADE B4 G4 B1 -40'- G1 B3 I. C2 III G2 3 C3 -20'- C4 2 @ 10' 20' = 5 @ 8' 40' C1

P2.3. Consider the floor plan shown in Figure P2.3. Com- pute the tributary areas for (a) floor beam B1, (b) floor beam B2, (c) girder G1, (d) girder G2, (e) corner column C1, and (f) interior column C2. (A) (B C I B2 I G3 I (2) 6 @ 6.67' = 404 I HADE B4 G4 B1 -40'- G1 B3 I. C2 III G2 3 C3 -20'- C4 2 @ 10' 20' = 5 @ 8' 40' C1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The floor system of a factory consists of a 5”-thick normal weight reinforcedconcrete slab resting on four steel floor beams (A = 14 in2) that, in turn, aresupported by two steel girders (A = 40 in2), as shown in the plan below.a. Should this slab be idealized as one-way spanning or two-way spanning?b. Draw the free-body diagram for the dead loads on beam BF and label themagnitude of all loads.c. Draw the free-body diagram for the dead loads on girder AD and label themagnitude of all loads.d. What is the axial load carried by column A?
Note: draw its fbd and solve
Q1. Determine the vertical displacement of end C of the precast concrete column. Econcrete = 4.2 (10³) ksi.
A short spiral column carries an axial dead load of 118 kN and an axial live load of 235 kN. Use fc’ = 27.5 MPa, fy = 414 MPa. Use U = 1.2D + 1.6L, Ф = 0.65 1. Assuming ρ = 0.01, which of the following gives the diameter of the column section? * a. 200 mm b. 215 mm c. 220 mm d. 300 mm 2. Which of the following gives the number of 16 mm diameter main bars? a 3 pcs b. 4 pcs c. 5 pcs d. 6 pcs 3. Which of the following gives the spacing of spirals? a. 10 mm Ф b. 55 mm Ф c. 60 mm Ф d. 65 mm Ф
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
Determine support reaction. P=800 lb , a=5 ft b=9 ft
Using the tributary area method, compute the floor dead loads supported by columns Al and B2 in Figure 1. The floor system consists of a 6in thick reinforced concrete slab weighing 75 Ib/ft^2. Allow 15 Ib/ft^2 for the weight of floor beams, utilities, and a ceiling suspended from the floor. In addition, allow 10 Ib/ft^2 for lightweight partitions. The precast exterior wall supported by the perimeter beams weighs 600 Ib/ft.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steelbeams (A=9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown.Determine the dead loads acting on beam BF and girder AD. Assume 23.6 kN/m3 unit weight of concrete and 77.0 kN/m3 for steel.
The floor system of an apartment building consists of a 4-in, thick reinforced concrete slab resting on three steel floorbeams, which in turn are supported by two steel girders, asshown. The areas of cross section of the floor beams andthe girders are 18.3 in^2 and 32.7 in^2.,respectively.Determine, the total load carried by girder AE. Unit weight of Steel: 490 lb/ft^3;concrete: 150 lb/ft^3;Live load for Apartment Bldg. : 40 psf
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN