I need an answer quickly please (A) Fill in the blankets1. The control volume expression for the conservation of massis the ..............2. The fluid viscous or frictional effects can be neglected only ifthe fluid is considered to be.............3. If the energy grade line (EGL) is known, then the hydraulicgrade line (HGL) will always be..............below the EGL.4. The entrance length (L') is a functi of the pipe diameter(D) and the Reynolds number (Re). and for laminar flow inpipes, the upper limit to the entrance length. L'=.........5.is occurred at the bottom of a chute or spillway andit is characterized by a localized turbulence that rapidlydissipates kinetic energy from the flow.

as per guidelines i have to solve only question of yours ,please repost remaining one. given = fill…

(A) Fill in the blankets 1. The control volume expression for the conservation of mass is the... 2. The fluid viscous or frictional effects can be neglected only if the fluid is considered to be............... 3. If the energy grade line (EGL) is known, then the hydraulic grade line (HGL) will always be............below the EGL.

(A) Fill in the blankets 1. The control volume expression for the conservation of mass is the... 2. The fluid viscous or frictional effects can be neglected only if the fluid is considered to be............... 3. If the energy grade line (EGL) is known, then the hydraulic grade line (HGL) will always be............below the EGL.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
Pls. answer thank you! In Francis turbine, the pressure gage leading to the turbine casing reads 385 kpa and center of spiral casing is 3.5 m above the tailrace. If the velocity of water entering the turbine is 9 m/s, what is the net head of the turbine?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Water (density 1000 kg/m?) flows through an inclined pipe of unform diametar. The velocity. pressura and elevation at section A are V, = 3.2 mis, p, =186 kPa and 2, = 245 m respectively, and those at section B ara V = 3.2 /s, py = 260 kPa and 2y = 9.1 m, respectivoly. If accaleration due 1o gravity /s 10 m/s* then the head lost due to friction is ‘m (round off 1o one decimal place).
If a jet is inclined upward 30 degrees from the horizontal, what must be its velocity to reach over 3m wall at a horizontal distance 18m, neglecting friction?
A tank half full of water is accelerated to the right at 9.81 m/s^2. If the motion is laong the side with a length of 4 m, the water surface on the rear wall will: a. rise 2 m b. rise 1.5 m c. drop 2 m d. drop 1.5 m
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
Installing the suitable pump to deliver 300 litres per minute. can you expline this sentence and give more data about ? please write it in the answer in print font ?
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.
It is required to pump water at 100 gal/min from a large reservoir to the surface of another reservoir 400 feet higher. What is the horsepower of the motor to drive the pump if the efficiency of the pump is 70%?
a. the total head loss due to friction (HL = hfs + hfd) in meters b. the total dynamic head in meters c. the water power in kW