A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is held in place by a pin at A and a rocker at B as shown 2400 kg 1.5 m 2 m - 4 m- What are the components of the Tension Vector (T), which is used to represent the weight of the crate T= T,i – T,j Choos 9.81 (Answer in Kilo Newtons) -2.4 -23.54 2.4 Choose. T Choose. Ty = here to search

A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is held in place by a pin at A and a rocker at B as shown 2400 kg 1.5 m 2 m - 4 m- What are the components of the Tension Vector (T), which is used to represent the weight of the crate T= T,i – T,j Choos 9.81 (Answer in Kilo Newtons) -2.4 -23.54 2.4 Choose. T Choose. Ty = here to search

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The homogeneous plate of weight W is suspended from two cables. Determine the force P that is necessary to keep the plate in the position shown.
A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
1. Samer (ms = 75 kg) is sitting on the seat of a swing at the playground. The seat is supported by two cables, one on each side of the seat. (You may assume the seat has negligible mass.) A. Determine the tension in each cable due to Samer sitting on the swing seat. B. Given each cable has a diameter of 1 mm and each cable is exactly 5 m long before Samer sits on the seat, determine the length of each cable when Samer is sitting on the seat. (The cables are made of Aluminum for which Y = 70 GN/m°.) show all work in logical, detailed form and box in numerical answers. Include a diagram wherever possible. On any problem where an FBD is appropriate, it must be included for maximum credit. All numerical results should be stated to 3.00 or 4.000 significant figures and in mks units unless otherwise noted.
. The small piston of a hydraulic lift (g. 1) has a cross-sectional area of 3.00cm2, and its large piston has a cross-sectional area of 200cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0kN?
Determine the force in each member of the truss (positive value for tension and negative for compression). Given: P1 = 20 N, P2 = 10 N.
In the figure shown, the large piston on the left has a diameter of D1 = 9.00 cm.The small piston on the right has a diameter of D2 = 4.00 cm.A lever arm pivot is located a = 5.00 cm to the left of the small piston.A small cylinder hangs from the end of the lever arm a distance b = 25.0 cm to the right of the small piston.In the absence of friction, determine the weight of the cylinder on top of the large left piston which can be supported in equilibrium with the small mass (m = 0.350 kg)hanging from the far right lever arm.Provide a force vector diagram (free body diagram).
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
First image: How to determine the tension in the cable and the normal force on thesmooth inclined surface given that W = 100 lb?Second image: How to determine the tension when (gravity) g = 9.81 m/s2?