A frictionless piston-cylinder device initially contains 0.2 kg of steam at 400 kPa, 300 °C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 135 °C. |frictionless Piston Steam ,m=0. 2 kg PI= 400 kPa Ti= 300°C (sat. liq.)2 T3 = 135 Stops %3D

A frictionless piston-cylinder device initially contains 0.2 kg of steam at 400 kPa, 300 °C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 135 °C. |frictionless Piston Steam ,m=0. 2 kg PI= 400 kPa Ti= 300°C (sat. liq.)2 T3 = 135 Stops %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When pumping water (Q = 10 L/s, η = 60%, 10 kW shaft power), water temperature in pump rises roughly by
In a tank with a height of 1 meter, open to the atmosphere at the top, there are two immiscible liquids (which do not mix) and whose densities are 13,600 kg/m3 and 750 kg/m3, respectively. The tank is completely full and each liquid occupies half of the container. If the atmospheric pressure of the place is 105 Pa, at what depth, measured from the top of the tank, is the value of the gauge pressure equal to half the value of the atmospheric pressure of the place? Consider that the gravitational acceleration of the place is 9.8 m/s2? a) 84.76 cmb) 34.75 cmc) 50.00 cmd) 37.51 cm
A storage tank, 26 ft in diameter and 36 ft high, is fi lledwith SAE 30W oil at 20 ° C. ( a ) What is the gage pressure,in lbf/in 2 , at the bottom of the tank? ( b ) How does your resultin ( a ) change if the tank diameter is reduced to 15 ft?( c ) Repeat ( a ) if leakage has caused a layer of 5 ft of waterto rest at the bottom of the (full) tank.
An airtight dispenser for drinking water is 25 cm × 10 cm in horizontal dimensions and 20 cm tall. It has a tap of negligible volume that opens at the level of the bottom of the dispenser. Initially, it contains water to alevel 3.0 cm from the top and air at the ambient pressure, 1.00 atm, from there to the top. When the tap is opened, water will flow out until the gauge pressure at the bottom of the dispenser, and thus at the opening of the tap, is 0. What volume of water flows out? Assume the temperature is constant, the dispenser is perfectly rigid, and the water has a constant density of 1000 kg/m3
As measured by NASA’s Viking landers, the atmosphereof Mars, where g ≈ 3.71 m/s 2 , is almost entirely carbondioxide, and the surface pressure averages 700 Pa. The temperatureis cold and drops off exponentially: T ≈ T o e - Cz ,where C = 1.3E-5 m - 1 and T o = 250 K. For example,at 20,000 m altitude, T ≈ 193 K. ( a ) Find an analyticformula for the variation of pressure with altitude.( b ) Find the altitude where pressure on Mars has droppedto 1 pascal.
Early mountaineers boiled water to estimate their altitude.If they reach the top and fi nd that water boils at 84 ° C,approximately how high is the mountain?
As2...Suppose that we could increase the atmospheric pressure on the surface of Mars to 0.2 bar, by vaporizing the polar caps and subsurface ice. This atmosphere would then likely decrease over time, as a result of several processes, such as escape into space, and erosion by the solar wind. How would the surface pressure decrease as a function of time? How much time would it take until the pressure is only 0.1 bar?
The fuel consumption of an automobile is 14 km/ L.The fuel consumption, in miles per gallon, is?
At 28oAPI specific gravity, what is heating value of oil in kJ/kg?
If 10 m^3 of atmospheric air at 1 degree centigrade temperature are compressed to a volume of 1m^3 at 100°C, what will be the pressure of air?
The figure below shows a turbine-driven pump that provides water to a mixing chamber located dz⁢= 5 m higher than the pump, where m˙=50 kg/s. Steady-state operating data for the turbine and pump are labeled on the figure. Heat transfer from the water to its surroundings occurs at a rate of 2 kW. For the turbine, heat transfer with the surroundings and potential energy effects are negligible. Kinetic energy effects at all numbered states can be ignored. Determine:(a) the magnitude of the pump power, in kW.(b) the mass flow rate of steam, in kg/s, that flows through the turbine.
A piston-cylinder arrangement contains water at 110°C, 85% quality with a volume of 1 L. What is the initial mass, in grams? The system is heated, causing the 150-mm-diameter piston to rise and encounter a linear spring with k = 800 kN/m. Calculate the specific internal energy (kJ/kg) at this instant knowing that the measured volume is 1.65 L. The heating continues and compresses the spring in the process. When the piston encounters the stops, the pressure is 200 kPa. What is the temperature (in °C) and entropy (in J/K) at this point? Heating continues until the pressure reached 300 kPa. What is the volume, in L at this instant? Illustrate the process in separate P-v and T-v diagram. Note:1000 L = 1m3. Hint: Draw the FBD of the piston in each state.