A frustum cone tank is initially filled with water asR 2wshown in figure. After that, the water drains through a holeof radius (r=0.05 m) is located at the bottom of tank.1- Find the depth of water at any time (y(t)).2- compute the time required to drain half volume ofwater in the tank.whereR=ww = 2mg = 10 m/s?

Name: A frustum cone tank is initially filled with water asR 2wshown in fig
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A frustum cone tank is initially filled with water asR 2wshown in figure. After that, the water drains through a holeof radius (r=0.05 m) is located at the bottom of tank.1- Find the depth of water at any time (y(t)).2- compute the time required to

Engineering

Mechanical Engineering

A frustum cone tank is initially filled with water as shown in figure. After that, the water drains through a hole of radius (r-0.05 m) is located at the bottom of tank. R= 2w 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R=w w = 2m g = 10 m/s?

A frustum cone tank is initially filled with water as shown in figure. After that, the water drains through a hole of radius (r-0.05 m) is located at the bottom of tank. R= 2w 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R=w w = 2m g = 10 m/s?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read the question carefully and give me all right solutios. A 2.4 m diameter tank is initially filled with water 5.5 m above the center of a 10 cm diameter, sharp-edged hole. The surface of the water tank is open to the atmosphere, and the hole drains to the atmosphere. If you neglect the effect of the kinetic energy correction factor, calculate: a) the initial flow rate of the tank and b) the time it takes to empty the tank.c) Does the orifice loss coefficient cause a significant increase in tank drain time? yes or no, the emptying time for this case is t =
Water from a storm drain fl ows over an outfall onto aporous bed that absorbs the water at a uniform verticalvelocity of 8 mm/s, as shown in Fig. P3.19. The system is5 m deep into the paper. Find the length L of the bed thatwill completely absorb the storm water.
Fluid flowing horizontally at 100gpm from a 2-in-diameter pipe to a 1-in-diameter pipe asshown in Figure. If the pressure at point 1 is 10 psi, find the pressure at point 2. Thespecific gravity of the fluid is 0.9.
The cylindrical water tank in Fig. is being fi lled ata volume fl ow Q 1 = 1.0 gal/min, while the water alsodrains from a bottom hole of diameter d = 6 mm. At timet = 0, h = 0. Find and plot the variation h ( t ) and the eventualmaximum water depth h max . Assume that Bernoulli’ssteady-fl ow equation is valid.
The square-section duct in atmospheric conditions is exposed to outside air flow as seen in the figure. The temperature of the air is T air= 5°C, the velocity is V air= 10m/s. Find the exit temperature of the water entering the channel at a flow rate of ṁwater=0.01 kg/s and a temperature of T water,g=50°C. Geometric dimensions are given on the figure.
The water flow between large tanks is steady and steady, and the pipe diameters are indicated in the figure. Calculate the height of ha when hb = 2 m according to the figures given in the figure.(g = 9.81 m/s2 , density of water 1000kg / m3.)
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
At the end of the summer, a swimming pool is being drained through a very long,small-diameter hose. The hose is smooth, of inner diameter D = 6.0 cm,and of length L = 65 m. The initial height difference from the pool surface to theoutlet of the hose is H = 2.20 m. Calculate the volume flow rate in litres per minute(LPM) at the start of draining.
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asurf= 6 m^2. At the bottom of the tank there is a door inclined at an angle θ= 40 degrees with respect to the horizontal. The door has a length L=1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Qi(t)=0.27 m^3/s and the flowrate out is Qo(t)= 0.09 m^3/s At time t=0, the water has a depth h0= 2 m. The density of water is ρ=1000 kg/m^3. a) Find the pressure (in kilopascals) at time t=0 b) Find the vertical force (in Newtons) on the door at time t=0c) Find the height (in metres) of the fluid at time t=100 s
A 40-cm straight pipe is used to carry water at 20°C from one reservoir to another reservoir that is 0.7 km away. There is an elevation difference of 9 m between the two reservoirs, Determine the discharge is the pipe is commercial steel.