QUESTION 3 Some hydraulic machines are served with water under pressure by a pipe 300 m long, the pressure at the machines being 4140 kN/m?. The power available at the machines is 220 kW and the frictional loss of power in the pipes is 88 kW. If f = 0,03, find The necessary diameter of pipes. The pressure at the pumping end. The maximum power at which the machines could be worked for the same pump pressure? 3.1 3.2 3.3

QUESTION 3 Some hydraulic machines are served with water under pressure by a pipe 300 m long, the pressure at the machines being 4140 kN/m?. The power available at the machines is 220 kW and the frictional loss of power in the pipes is 88 kW. If f = 0,03, find The necessary diameter of pipes. The pressure at the pumping end. The maximum power at which the machines could be worked for the same pump pressure? 3.1 3.2 3.3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
An orifice of diameter 150 mm is fitted at the bottom of a boiler drum lenth 6 m and of diameter 2 m. The drum is horizontal and contains water up to height of 1.8 m. Find the time required to empty the boiler. Take Cd=o 0.60. Include FBD. a. 127 seconds b. 217 seconds c. 467 seconds d. 175 seconds
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
If you have a closed system that is filled with water on 2bar, the pump is selected for pressure losses due friction of the pipes(1bar) 1/ why don't we have to take pressure losses due height in account? 2/ what is the pressure at 100 m height inside the system? When the pump stops? And when the pump is circulating, prove your answer figure in image
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Pls. answer thank you! A pelton type turbine was installed 31m below the head gate of the penstock. The head loss due to friction is 15% of the given elevation. The length of the penstock is 80 m and the coefficient of friction is 0.00093 (Morse). Determine the diameter in meters of the penstock and the power output in KW.
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
a pump must pump 4800 gpm against a total head of 80 ft. what horsepower will be required to do the work? Answer: 97 hp
The owners of a smallholding water their vegetable garden using collected rainwater from atank. Thetankhasadiameterofbm,itisam tall and sits on a 6 m tall stand. The inner diameter of the hose is c cm, and the hose is (20 +5d) m long. If the tank was initially filled to the brim, how long will it take before the tank is empty? Assume that there is a single ball valve (K = 0.05) in the line, and that the spray nozzle has a hole diameter that is 20 % of the diameter of the hose. You may ignore all other losses in the nozzle. a = 9 b = 8 c = 7 d = 1 Hint: Use an Excel spreadsheet or C program for the calculations.
I2 4.2, there is friction in the piping, which means that an additional pressure equivalent to a height of 100 m is needed to pump the water from the bottom tank to the top tank. What is the minimum power required when accounting for friction? By what percentage has friction increased the minimum power required? Remember to show your calculations.