A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitudes are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c= 5 in. Determine the normal and shear stresses on the outer surface of the pipe at point H and show these stresses on a stress element. Z Answer: Oy Txy i y H K -2715 i 600.7 b Pz Py X psi psi

A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitudes are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c= 5 in. Determine the normal and shear stresses on the outer surface of the pipe at point H and show these stresses on a stress element. Z Answer: Oy Txy i y H K -2715 i 600.7 b Pz Py X psi psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of 0.373 in. The pipe is subjected to a uniformly distributed torque oft= 63lb-ft/ft along its entire length. Using a = 2.25 ft, b = 4.00 ft, and c= 8 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe.
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
The frame shown in figure shows three pinned end bars AB,BD, and CD. The bars are of identical material and cross-section 600 mm^2, and the ultimate stress capacity of each is 350MPa. Using factor of safety of 2.5 , determine the ultimate vertical load P that may be applied to the system at point D.
Knowing that the allowable stress in section a-a is 90 MPa, determine the largest force that can be exerted by the press shown. The largest force that can be exerted by the press is
A torque of T = 5400 kN-m is applied to a torsion member whose cross section is shown. Dimensions of the cross section are a = 660 mm, b = 1140 mm, d = 1670 mm, t1 = 19 mm, t2 = 10 mm, and tz = 15 mm. The dimensions given for a, b, and d are measured to the wall centerline. Determine the average shear stress acting at points A. B, and C.
a signage is connected to a pole as shown in the figure. if the pole is a hollow shaft with ouside and inner diameter s 100mm and 70mm respectively. A wind pressure of 2kN/m^2 is acting on the signage . Given a= 200mm b=2m c=1m d=4m. 1. Determine the shearing stress (Mpa) at the base of the pole. a.1.25 b.1.96 c 2.1 d1.5 2.Determine the maximum bending stress (MPa) in the hollow shaft. a.248.28 b.241.28 c.255.23 d.312.54 3. Determine the torsional shearing stress (MPa) a.25.05 b 18.59 c.34.85 d.32.17 Answer. 1.96,241.28,32.17
1. Calculate the total length, L (m) so that the resulting stress, q is uniform. 2. Which of the following gives the location (m) of the maximum shear from the left end? 3. Which of the following gives the location (m) of the point of inflection from the left end?
Compute the stress at each segment of the pipe.
A torque of T = 5100 kN·m is applied to a torsion member whose cross section is shown. Dimensions of the cross section are a = 510 mm, b = 1000 mm, d = 1640 mm, t1 = 20 mm, t2 = 10 mm, and t3 = 15 mm. The dimensions given for a, b, and d are measured to the wall centerline. Determine the average shear stress acting at points A, B, and C.
A simply supported wood beam with overhang is subjected to uniformly distributed load q. * Inserted Photo * The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm.Determine the maximum permissible value q if the allowable bending stress is ?all = 11.2 MPa, and the allowable shear stress is ?all = 1.50 MPa. (Enter the magnitude in kN/m.)
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
b) Determine the shear stress on the outer surface of the pipe at point H -34.5 MPa -45.5 MPa -23.9 MPa -40.6 MPa -16.6 MPa c) Determine the normal stress on the outer surface of the pipe at point H -207.8 MPa -151.4 MPa -135.5 MPa -103.5 MPa -177.4 MPa Please do all the three sub parts