A hollow steel drive shaft working in a high speed machine is shown in the figure and has an outer diameter of 100 mm and a wall thickness of 15 mm. During a particular loading situation, the shaft is subjected to a uniformly distributed load of magnitude 1.75 kN/m and an axial tensile load of magnitude 110 kN as shown. Also, during service, the shaft rotates at a speed of 500 rev/min and transmits a power of 300 kW. The shaft steel is ductile and has a yield strength in tension of 200 MN/m', an ultimate tensile strength of 475 MN/m² and a Modulus of Rigidity of 81 GN/m. Also, the shaft was designed to have a minimum factor of safety of 2. i) Calculate the component stresses set-up in the shaft material at point X' (bottom surface of the shaft at midspan as indicated in the figure) due to the loading conditions. ii) Determine the magnitude and nature of the principal stresses, and the maximum shear stress analytically and graphically, and the angle of the planes on which the major principal stresses act at point X'. iii) By applying the appropriate yield criteria, evaluate the factor of safety for the shaft and

A hollow steel drive shaft working in a high speed machine is shown in the figure and has an outer diameter of 100 mm and a wall thickness of 15 mm. During a particular loading situation, the shaft is subjected to a uniformly distributed load of magnitude 1.75 kN/m and an axial tensile load of magnitude 110 kN as shown. Also, during service, the shaft rotates at a speed of 500 rev/min and transmits a power of 300 kW. The shaft steel is ductile and has a yield strength in tension of 200 MN/m', an ultimate tensile strength of 475 MN/m² and a Modulus of Rigidity of 81 GN/m. Also, the shaft was designed to have a minimum factor of safety of 2. i) Calculate the component stresses set-up in the shaft material at point X' (bottom surface of the shaft at midspan as indicated in the figure) due to the loading conditions. ii) Determine the magnitude and nature of the principal stresses, and the maximum shear stress analytically and graphically, and the angle of the planes on which the major principal stresses act at point X'. iii) By applying the appropriate yield criteria, evaluate the factor of safety for the shaft and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the maximum tensile and compressive stress in the link if the thrust is 2500 N. (Cam bridge) ANSWER: maximum tensile 38.0 MN/m2; maximum compressive 46.0 MNIm2. Please show the solution to get the answer.
P=40 kN E=190GPa l=1.6 m Ø=17 mm
Property ASTM A710 Steel AA 7075 Density 7.8 2.81 Yield Strength 585 503 Ultimate Tensile Strength 620 572 Poisson Ratio 0.29 0.33 Shear Modulus 80 26.9 Young’s Modulus 205 71.7 Dimensions Side bar (C-Channel) = 210 x 76 x 6 mm Front Overhang = 935 mm Rear Overhang = 1620 mm Wheel Base = 3800 mm Width = 2250 mm Capacity = 8000 x 9.81 = 78480N Capacity with 1.25% = 98100N Weight of body and engine = 19620N Total load = 117720N Load acting on a single bar of chassis = 58860N Using the information above for two materials Iron (ASTM A710 Steel ) and Aluminum (AA 7075) Calculate for each Material Reaction Force Shear Forces Bending Moment Bending Stress Shear Stress Von Misses Stress Principle Stress Max Shear Stress Total Deflection Draw the Shear Force and bending moment Diagram for each Material. Draw the Equivalent Mohr Circle for each material Conclude with a Comparison of the Deformation of the two Materials.
average shear stress = 50.4 MPa angle of twist per unit length = 3.06 deg/m
The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a. 14.72x109 N-m b. 14.72 kN-m c. 147.2 N-mm d. 14.72 N-m
ε0= 0.005B (hr-1Pa-1)=4.20E-34n=3.15 σ0 (Pa)= 550000000
4kN/m uniform spring load h = 2b allowable normal stress 12MPa h(min) = ?
1) A flange coupling connects two 50mm shafts. The flanges are fitted with 4 bolts of SAE1040 steel on an 80mm bolt circle. The shaft runs @ 360 rpm & transmits 30kW. Assume a factor of safety 4, ultimate tension of 490x103 kPa; ultimate shear of 400x103 kPa, determine: (a) the torque transmitted in kN-m; (b) the minimum diameter of the bolts required based on commercial sizes; (c) the minimum thickness of the flange.
L=9m W=5kN/m 360 UB 50.7
The shaft whose torque varies from 3000 to 7000 in-lbs has 1.5 inches in diameter and 65,000 psi yield strength. Compute for the shaft mean average stress. d.6,036 psi c.11,909 psi b.8,904 psi a.10,377 psi
Please help :( given: T(sub B) = 80.11, T = 5.67 kN-m
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 16 mm d = 120 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1737 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 254790000 mm4. If the beam will be subjected to a shear force of V = 250 kN, determine the shear stress at point K, located at yK = 80 mm below the z centroidal axis.