Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: Elastic Modulus, E = 200 GPa and Shear Modulus, G = 75 GPa. Determine the following: (a) Absolute maximum torsional shear stress b) Angle of twist of the end B with respect to the support Show complete solution (FBDs and equilibrium equations).

Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: Elastic Modulus, E = 200 GPa and Shear Modulus, G = 75 GPa. Determine the following: (a) Absolute maximum torsional shear stress b) Angle of twist of the end B with respect to the support Show complete solution (FBDs and equilibrium equations).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).
Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.
The solid cast-iron shaft shown in Fig.a is subjected to a torque of T = 400 lb # ft. Determine its smallest radius so that it does not fail according to the maximum normal stress theory. A specimen of cast iron, tested in tension, has an ultimate stress of (sult)t = 20 ksi.
Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected to a torsional moment of 500 Nm. The shaft is made of a material with a shear modulus of 80 GPa. Determine the maximum shear stress and the angle of twist along the length of the shaft. Problem 2: A solid circular shaft of length 3 meters is made of a material with a shear modulus of 60 GPa. The shaft has a diameter of 80 mm and is subjected to a torque of 600 Nm. Due to manufacturing constraints, the maximum allowable shear stress for the material is 60 MPa. Determine if the shaft design is safe and, if not, suggest an alternative design to meet the given constraints.
The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque TO that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. (Please provide detailed solution, thank you with FBD) To = ? lb-in ϴBC = ? degree