A solid rotating shaft made of Annealed AISI 1030 is used in a boat with a high speed as shown in the figure. The transmitted power is 224 KW with Revolutions number 130 rpm. Use the failure criteria to determine the shaft diameter and which one is more conservative. Take n=1 and endurance limit 18.86 Kpsi. Man to 100 mm 9.75 m

A solid rotating shaft made of Annealed AISI 1030 is used in a boat with a high speed as shown in the figure. The transmitted power is 224 KW with Revolutions number 130 rpm. Use the failure criteria to determine the shaft diameter and which one is more conservative. Take n=1 and endurance limit 18.86 Kpsi. Man to 100 mm 9.75 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Similar questions

A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
Find the diameter of the propeller shaft, which has to transmit power of 1.5 kW at 8 Hz without exceeding shear stress of 25 MPa.
A ship's shaft operates at 150 rpm and resists a maximum shear stress of 50 MPa. The shaft has an outer diameter of 45 cm and an inner diameter of 30 cm, as shown in the figure. Determine: What is the maximum power that can be transmitted without exceeding the allowable shear stress? If the rotational speed of the shaft is limited to half, but the same shaft power is maintained, what happens to the shear stress in the shaft?
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
A solid 22-mm-diameter bronze shaft transmits 13.4 kW at 17 Hz to the propeller of a small sailboat. Determine the maximum shear stress τmax produced in the shaft.
A hollow shaft transmits 9 MW at 300 rev/min. It is supposed that the maximum allowable stress is not to exceed 70 MN/m2 nor the angle of twist 0.5 degree per metre length of shafting. If the outside diameter of the shaft is 400 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m2. *
A hollow shaft is required to transmit 700 kW at 110 r.p.m., the maximum torque being 20% greater than the mean. The shear stress is not to exceed 78MPa and twist in a length of 9.84 feet not to exceed 1.4 degrees. Find the external diameter of the shaft, if the internal diameter to the external diameter is 3/8. Take modulus of rigidity as 79 GPa.
The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.
A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft
A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A solid shaft is transmitting 1MW at 240rpm . Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%.Take the maximum allowable shear stress are 60MPa.