A layout of the outlets, switches, dimmers, track lighting, and recessed luminaires is shown in the following diagram. Using the cable layout of Figure 13-1, make a complete wiring diagram of this circuit. Use colored pencils or marking pens to indicate conductors. GFCI WP R17 Track ightng Denmer Living Room This eceptace a connected to the SudyBearoom droul

A layout of the outlets, switches, dimmers, track lighting, and recessed luminaires is shown in the following diagram. Using the cable layout of Figure 13-1, make a complete wiring diagram of this circuit. Use colored pencils or marking pens to indicate conductors. GFCI WP R17 Track ightng Denmer Living Room This eceptace a connected to the SudyBearoom droul

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter13: Lighting Branch Circuit For The Living Room

Section: Chapter Questions

Problem 14R: A layout of the outlets, switches, dimmers, track lighting, and recessed luminaires is shown in the...

See similar textbooks

Similar questions

L1. Boxes are classified by type, construction, andA. installation location.B. luminaire support capability.C. number of knockouts.D. power rating L2. Which of the following devices must be placed at each end of an armored cable to prevent damage tothe conductors?A. An insulating sliderB. An insertion couplingC. An antishort bushingD. A metal loop fitting L3. Which of the following is the maximum cross-sectional conductor fill area for underfloor raceways?A. 50%B. 60%C. 40%D. 30%
15. What does a grounding symbol on a construction drawing convey?A. A single ground rodB. A grounding electrode systemC. A ground-fault current pathD. An equipment grounding conductor
Using the cable layout shown in Figure 14-1, make a complete wiring diagram of Circuit A21. Use colored pencils or pens.
3.a. When feeders or branch circuits are installed to supply a separate building or structure, a/an _______must also be installed.A. snap switchB. junction boxC. equipment grounding conductorD. supply conductor3.b. How many system bonding jumpers normally are there for a separately derived system that's grounded?A. TwoB. OneC. ZeroD. Three
12.a. FMC and LFMC wiring methods are permitted to be used for service-entrance conductors in lengths ofup toA. 12 feet.B. 9 feet.C. 6 feet.D. 3 feet. 12.b. The NEC states that service-drop conductors with voltage limited to 300 volts to ground shall have aminimum of _______ feet vertical clearance from final grade over residential property, driveways, andthose commercial areas not subject to truck traffic.A. 12B. 20C. 15D. 18
11.a. Which of the following is a point where a grounding electrode conductor connection must be made inthe communication system?A. The flexible nonmetallic power service racewayB. The grounding electrode conductor or metal enclosure for a grounding electrode conductorC. The space opposite the service equipment enclosureD. The grounded exterior metal water piping system within six feet of the point where it enters the building11.b. The equipment grounding conductor of a pump motor for a swimming pool must be grounded with asolid copper conductor that's no smaller thanA. AWG 8.B. AWG 12.C. AWG 10.D. AWG 6.
Which of the following products are not suitable for bonding on the supply side of the service disconnecting means? a) Threaded hubs b) Bonding bushings with jumpers c) Standard locknuts d) Threadless connectors made up tight
Equipment Grounding 13. A metal elbow is a part of a nonmetallic, underground raceway. The elbow won't need to be grounded as long as it's encased in at least _______ inches of concrete. A. 4 B. 5 C. 2 D. 6 13 A. Which of the following can be in the form of a wire and is required to be installed with feeders and branch circuits? A. Phased neutral conductorB. Equipment grounding conductor C. Grounded neutral conductorD. Grounding electrode conductor
A wiring job requires 7,645 feet of cable. If the cable comes in 250 ft. coils, how many coils of cable are required?
In both exposed and concealed locations, where a cable or raceway-type wiring method is installed through bored holes in joist, rafters, or wood members, holes shall be bored so that the edge of the hole is not less than ____ in. from the nearest edge of the wood member. Select one: A. 1/16 B. 1.6MM C. 1 D. 1 1/4
5.a. Typically, the bonding conductor installed between the panelboard equipment grounding terminal barsmust be continuous. It's only allowed to be broken where it connects to theA. signal reference grid.B. terminal bar in the panelboard.C. branch circuit.D. service entrance enclosure.5.b. An electrical system that's not grounded and is between 120 and 1000 volts must include the use ofA. arc suppression.B. ground isolators.C. ground detectors.D. equipotential barriers.
Circle the correct answer to the following statements: a. Type SE service-entrance cable is for aboveground use. True False b. Type USE service-entrance cable is suitable for direct burial in the ground. True False c. Type SE cable with an uninsulated neutral conductor is permitted for hooking up an electric range in a new branch circuit. True False d. Type SE cable with an insulated neutral conductor is permitted for hooking up an electric range in a new branch circuit. True False e. Are Types SE and USE service-entrance cables used in your area? Yes No