A one-pole amplifier offers a voltage gain of 10,000 (A=10,000) and a 3-dB cut-off frequency of 100 Hz. An analog design engineer uses this amplifier to build an amplifier with negative feedback. The closed-loop gain of the amplifier with negative feedback is 50. a) The loop gain (kAo) b) The 3-dB bandwidth of the amplifier with negative feedback is kHz.

A one-pole amplifier offers a voltage gain of 10,000 (A=10,000) and a 3-dB cut-off frequency of 100 Hz. An analog design engineer uses this amplifier to build an amplifier with negative feedback. The closed-loop gain of the amplifier with negative feedback is 50. a) The loop gain (kAo) b) The 3-dB bandwidth of the amplifier with negative feedback is kHz.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Question 2 Part (A) Design an inverting amplifier with a gain of 4. Use an ideal ops amp, a 30kΩ resistorin the feedback path, and ±12V power supplies. Part (B) Using your design from part (a), determine the range of input voltages that will keepthe op amp in the linear operating regions. Part (C) Suppose you wish to amplify a 2V signal, using your design from part (a) with avariable feedback resistor. What is the largest value for the feedback resistance thatkeeps the op amp in the linear operating region? Using this resistance value, what isthe new gain of the inverting amplifier.
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
An op-amp has an open-loop gain of 104 and a dominant open-loop pole at 4Hz. If an inverting amplifier with a gain of -100 is made from this op-amp, what is the resulting amplifier bandwidth? What is the gain-bandwidth product?
solve a,b and c please. a. Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET? b. Compare inverting and non-inverting amplifier? c. calculate the closed loop gain of the circuit diagram given below.
An op-amp-based noninverting ampliﬁer has R1 = 15 kΩ, R2 = 30 kΩ, and RL = 20 kΩ. The op amp has an open-loop gain of 94dB , an input resistance of 30 kΩ, and an output resistance of 5 kΩ. Find the loop gain, ideal voltage gain, actual voltage gain, input resistance , and output resistance for the feedback ampliﬁer.
Design an inverting amplifier to provide a closed-loop voltage gain of Ay = -22 V/V. The maximum input voltage signal is 30 mV with a source resistance in the range of 1 kls R, < 3 kN. The variable source resistance should introduce a difference in the gain no more than a 2% of the gain factor. What is the range in output voltage?
1. Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kΩ resistor in the feedback path, and ±12 V power supplies. 2. Using your design from part (a), determine the range of input voltages that will keep the op amp in its linear operating region. 3. Suppose you wish to amplify a 2 V signal, using your design from part (a) with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
The upper critical frequency of an op-amp’s open-loop response is 200 Hz. If the midrange gain is 175,000, answer the following: What is the ideal gain at 200 Hz? What is the actual gain? What is the op-amp’s open-loop bandwidth?
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
A certain op-amp is used in a feedback configuration having a gain of 20 and a bandwidth of 500 kHz. a)If the external resistor values are changed to increase the gain to 40, what is the new bandwidth? The new bandwidth is 250khz What is the unity-gain bandwidth of the op-amp ??
A gain of 10 is required from a noninverting constant-multiplier op-amp circuit. If the input resistor is 9 k Ω, what should be the value of the feedback resistor? Rf=_____kohms
Consider the following statement: In feedback amplifiers, concerning the connections between the direct amplifiers and the feedbacks network, a shunt connectiın at the input part servers to set an increased versiın of the input impedance of the direct amplifier, whereas again a shunt connection at the output part services to set a decreased version of the output imdepance of direct amplifier. Explain what is wrong with the statement above by drawing representative circuit diagrams and outlining the necessary calculations.