A one-shell pass and two-tube passes heat exchanger must transfer 300 kW to a solution with a specific heat of 3.28 kJ/kg-K and change its temperature from 60 C to 88 C. Steam is available at 120 C. The unit convective coefficient is 3 200 W/m2-K for the inside and 8 500 W/m2-K for the outside. The thermal conductivity for the tubes is 115 W/m-K and the tubes have 4 cm OD and 3 cm ID and are 3

A one-shell pass and two-tube passes heat exchanger must transfer 300 kW to a solution with a specific heat of 3.28 kJ/kg-K and change its temperature from 60 C to 88 C. Steam is available at 120 C. The unit convective coefficient is 3 200 W/m2-K for the inside and 8 500 W/m2-K for the outside. The thermal conductivity for the tubes is 115 W/m-K and the tubes have 4 cm OD and 3 cm ID and are 3

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.3P

See similar textbooks

Similar questions

A cylindrical liquid oxygen (LOX) tank has a diameter of 1.22 m, a length of 6.1 m, and hemispherical ends. The boiling point of LOX is -179.4C. An insulation is sought that will reduce the boil-off rate in the steady state to no more than 11.3 kg/h. The heat of vaporization of LOX is 214 kJ/kg. If the thickness of this insulation is to be no more than 7.5 cm, what would the value of its thermal conductivity have to be?
3.14 A thin-wall cylindrical vessel (1 m in diameter) is filled to a depth of 1.2 m with water at an initial temperature of 15°C. The water is well stirred by a mechanical agitator. Estimate the time required to heat the water to 50°C if the tank is suddenly immersed in oil at 105°C. The overall heat transfer coefficient between the oil and the water is , and the effective heat transfer surface is .
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
Refrigerationa.) Explain why you can’t cool down your kitchen by leaving your refrigerator or freezer door open with your refrigerator plugged in for an extended period of time.b.) The condenser of a home refrigerator is commonly underneath the appliance, thus the condensing refrigerant exchanges heat with household air, which averages 70oF. It is proposed toreconfigure a refrigerator so that the condenser is in the garage, where the average yearly temperature is about 50oF. Assume a freezer temperature of 0oF, a minimum temperature difference of 10K for heat transfer, and an actual coefficient of performance of 60% that of a Carnot cycle. Calculate the Coefficient of Performance for both configurations and discuss the pros and cons of this proposal.c.) Which is the most effective way to increase the coefficient of performance of a Carnot refrigerator: to increase TC with TH held constant or to decrease TH with TC held constant? Justify mathematically. For a real refrigerator, do…
In a cyclic comprising of air compressor and expansion, workdone by a prism during the compression stroke is 9.2KJ and the heat rejected to the surrounding is 50KJ. During the expansion stroke workdone by air on the prism is 8.4KJ. a) Determine the quality of heat transferred to or from the system. Tullow oil has discovered a large volume of crude deposit at Cape-3-Point along the western coast of Ghana after years of intensive exploration. In the Company’s bid to start exploration, Green Ghana an environmental protection NGO took Tullow to court to prevent the Company from embarking on the said project citing numerous environmental concerns. b) As an energy and sustainability expert, what do you think are the side effects of the project and their remedies? A cooling water pump is operating at a speed of 1800rpm. Its flow rate is 1800L/minutes at a head of 14.4m and the power of the pump is 45kw. c) Determine the power required if the pump speed is increased…
The condenser of a room air conditioner is designedto reject heat at a rate of 15,000 kJ/h from refrigerant-134aas the refrigerant is condensed at a temperature of 408C. Air(cp 5 1005 J/kg?K) flows across the finned condenser coils,entering at 258C and leaving at 358C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/m2?K,determine the heat transfer area on the refrigerant side.
In a meat processing plant, it is required to cool 1500 kg of beef whose specific heataverage is 3.14 kJ/kg-°C to lower its temperature from 39 °C to 2 °C in 14 hours. It is required to estimate theenergy requirements necessary for meat cooling capacity, assuming that the cooling systemRefrigeration operates on an ideal vapor compression refrigeration cycle. A refrigeration unit is chosenwith refrigerant 134a with a condenser pressure of 1.4 MPa and an evaporator pressure of 240 kPa.Assume that the refrigerant enters the compressor as a saturated vapor and leaves the condenser as a saturated liquid.Calculate:a) The COPR or CDFR,b) The mass flow of the refrigerantc) The energy dissipated into the atmosphered) The cost of annual electrical energy, if the plant will operate with a load factor (FC) of 85% (100%-FC =8760 h/year). Consider the unit cost of electrical energy of $2.6 per kWh and the efficiency of the system90% motor-compressor.
Solving Thermal Properties Related Problems Determine the amount of heat removed from 1.5 kg of bologna (sausage) when cooled from 24°C to -7°C. Assume MC of 59% and at -7°C, 22% won’t be frozen.
Stainless steel type 304 [k = 16.3 W/m-K] from heat treatment was brought to a room @ 27C. It is in cube form and has an edge of side 20cm. Initially, the temp. of the steel from the heat treatment is 500C. The total effective heat transfer coefficient is 18 W/m2-K. How long will it take for the surface of the cube to be within 28 C of the room temp.?
A closed stirred-tank reactor with two compartmentsis shown in Fig. The basic idea is to feed the reactants continuously into the first compartment, where they will be preheated by energy liberated in the exothermic reaction,which is anticipated to occur primarily in the second com-partment. The wall separating the two compartments is quite thin, thus allowing heat transfer; the outside of thereactor is well insulated; and a cooling coil is built intothe second compartment to remove excess energy liberated inthe reaction. Both tanks are completely full at all times.Tests are to be conducted initially with a single-component feed (i.e., no reaction) to evaluate the reactor’s thermalcharacteristics.(a)Develop a dynamic model for this process under the conditions of no reaction. Assume that q0,Ti,andTc all may vary.(b)Make a degrees of freedom analysis for your model—identifying all parameters, outputs, and inputs that must beknown functions of time in order to obtain a solution.(c)In…
A PCB is cooled by a 40mmL x 40mmW x 20mmL aluminum block heatsink. If the top and bottom surface of the aluminum heatsink run 45degC and 85degC respectively, what is the heat rate through the aluminum block?