Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 3, Problem 3.14P
A thin-wall cylindrical vessel (1 m in diameter) is filled to a depth of 1.2 m with water at an initial temperature of 15°C. The water is well stirred by a
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The wall of a refrigerator is made of fiberglass insulation (k = 0.035 W/mK) glued between two 1 mm thick layers of metal plate (k = 15.1 W/mK). The refrigerated space is kept at 2°C, and the average heat transfer coefficients on the inner and outer wall surfaces are 4 W/m²K and 9 W/m²K, respectively. The average temperature in the kitchen is 24°C. It is observed that condensation occurs on the external surface of the refrigerator when the temperature of the external surface drops to 20°C.
Determine the minimum thickness of fiberglass insulation that should be used on the wall to prevent condensation on the outside surface.
....A journal bearing is to be used for a centrifugal pump where the shaft diameter is 50 mm and the bearing length is 80 mm. The ambient and bearing surface temperatures are 20°C and 45°C, respectively. Which of the following is the heat dissipated by the bearing if the heat dissipation coefficient is 280 W/m2-°C?
Group of answer choices
56 W
14 W
73 W
28 W
Consider a closed cylindrical reactor vessel of diameter D= 1 ft, and length L= 1.5 ft. The surface temperature of the vessel, T1, and the surrounding temperature, T2, are 390 deg. F and 50 deg. F, respectively. The convective heat transfer coefficient, h, between the vessel wall and surrounding fluid is 4.0 Btu/h . ft . ⁰F. Calculate the thermal resistance in ⁰F .h/Btu.
Chapter 3 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 3 - Consider a flat plate or a plane wall with a...Ch. 3 - 3.2 High-strength steel is required for use in...Ch. 3 - Prob. 3.3PCh. 3 - 3.5 In a ball-bearing production facility, steel...Ch. 3 - A 0.6-cm diameter mild steel rod at 38C is...Ch. 3 - Prob. 3.7PCh. 3 - Prob. 3.8PCh. 3 - 3.9 The heat transfer coefficients for the flow of...Ch. 3 - 3.10 A spherical shell satellite (3-m-OD,...Ch. 3 - Prob. 3.11P
Ch. 3 - Prob. 3.12PCh. 3 - Prob. 3.13PCh. 3 - 3.14 A thin-wall cylindrical vessel (1 m in...Ch. 3 - A thin-wall jacketed tank heated by condensing...Ch. 3 - 3.16 A large, 2.54-cm.-thick copper plate is...Ch. 3 - 3.17 A 1.4-kg aluminum household iron has a 500-W...Ch. 3 -
3.28 A long wooden rod at with a 2.5-cm-OD is...Ch. 3 - A mild-steel cylindrical billet 25 cm in diameter...Ch. 3 - Prob. 3.37PCh. 3 -
3.38 An egg, which for the purposes of this...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55arrow_forward2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.arrow_forwardA spherical object with a temperature of 700 oC, made of carbon steel with a diameter of 3 cm, will be cooled to 370 oC by an air flow with a temperature of 35 oC and a heat convection coefficient of 90 W/m2K. Calculate the time (s) required to cool the body, ignoring the temperature gradient inside the body and making any other assumptions you deem necessary. The heat transmission coefficient of carbon steel can be 45 W/mK, its density is 7800 kg/m3 and its specific heat is 480 J/kgK.arrow_forward
- A steel tube, with a thermal conductivity of 50 W /m K, has an inner diameter of 20-mm and outer diameter of 26-mm. Hot gases flow over the tube with a convection heat transfer coefficient of 200 W/m2 K; while, cold water flows through the tube with a convection heat transfer coefficient of 8000 W/m2 K. What is the hot-side overall heat transfer coefficient in W/m2 K?arrow_forwardHot water is to be cooled as it flows through the tubes exposed to atmospheric air. Fins are to be attached in order to enhance heat transfer. Would you recommend attaching the fins inside or outside the tubes? Why?arrow_forwardPulverized coal particles are used in oxy-fuel combustion power plants for electricity generation. Consider a situation where coal particles are suspended in hot air flowing through a heated tube, where the convection heat transfer coefficient is 100 W/m2·K. If the average surface area and volume of the coal particles are 3.1 mm2 and 0.5 mm3, respectively, determine how much time it would take to heat the coal particles to two-thirds of the initial temperature difference.arrow_forward
- A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Solving, the temperature at the surface of the fuel rod is 1026°C. I need the solution with fundamental concepts (Textically with definitions) of how the heat flow behaves in the system. NOT THE MATHEMATICAL RESOLUTION. I already know how to solve it.arrow_forwardA 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Solving, the temperature at the surface of the fuel rod is 1026°C. Explain how the heat flow behaves in the system, using the fundamental concepts.arrow_forwardA 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Determine the temperature at the surface of the fuel rod. Note: Give the solution from fundamental concepts of how the heat flow behaves in the systemarrow_forward
- In a food industry, pieces of meat with approximately 30 cm in diameter and 20 mm in thickness are stored in a industrial freezer and thawed by exposure to ambient air at 15°C with convective heat transfer coefficient equal to 10W/(m2.K). Consider a piece of meat that, when removed from the freezer, had a temperature of -12°C. For defrosting, the piece is hung on a "line", so that both larger surfaces are exposed to the ambient air. For frozen meat, the following properties can be assumed ρ=1090 kg/m3, cp=3.54 kJ/(kg.K), k=0.47 W/(m.K). Ask: (1) Indicating the control volume and the simplifications adopted, obtain the differential energy balance equation for the cooling the piece of meat and describe the conditions of outline and initial that apply to the process, justifying them; (2) Use the appropriate analytical solution to determine the time necessary for the complete defrosting of the part. The part is considered to be completely thawed when a minimum temperature of 5oC is reached…arrow_forwardThe wall of a refrigerator is constructed of fiberglass insulation (k = 0.035 W/m⋅K) sandwiched between two layers of 1-mm-thick sheet metal (k = 15.1 W/m⋅K). The refrigerated space is maintained at 2 °C, and the average heat transfer coefficients at the inner and outer surfaces of the wall are 4 W/m2⋅K and 9 W/m2⋅K, respectively. The kitchen temperature averages 24 °C. It is observed that condensation occurs on the outer surfaces of the refrigerator when the temperature of the outer surface drops to 20 °C. Determine the minimum thickness (in mm) of fiberglass insulation that needs to be used in the wall in order to avoid condensation on the outer surfaces.arrow_forward400 circumferential fins of rectangular profile (k = 386 W/m °C) are installed on a tube having a diameter of 3 cm and 1 m length that is maintained at a temperature of 200°C. The single fin has a length of 2 cm and a thickness of 0.7 mm. The heat is transferred to the surrounding air at 100°C with a convection heat-transfer coefficient of 524 W/m2 °C. How many times is the heat transfer rate enhanced when the fins are installed on the tube?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license