A pipeline connecting three tanks contains 10 standard long elbows, 5 globe valves that is half open, and 3 gates valve that is 1/4 open. The line is commercial steel pipe, 40 mm internal diameter, length 200 m. The properties of the fluid are: viscosity 0.99 mNm-2 s, density 998 kg/m3. Calculate the total pressure drop due to friction using velocity heads method when the flow rate is 4000 kg/h and f = 0.0032.

A pipeline connecting three tanks contains 10 standard long elbows, 5 globe valves that is half open, and 3 gates valve that is 1/4 open. The line is commercial steel pipe, 40 mm internal diameter, length 200 m. The properties of the fluid are: viscosity 0.99 mNm-2 s, density 998 kg/m3. Calculate the total pressure drop due to friction using velocity heads method when the flow rate is 4000 kg/h and f = 0.0032.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal pipe of diameter 350 mm converges to a diameter of 200 mm. The pipeconveys water with a density of 1 g/cm3. The pressure at the inlet and outlet are 550kPa and270 kPa respectively. Assuming the flow is incompressible and frictionless, estimate themass flow rate through the pipeline, stating the velocity at both the inlet and outlet.
It is desired to deliver 60 m3/h of water at 20°C through ahorizontal asphalted cast iron pipe. Estimate the pipe diameterthat will cause the pressure drop to be exactly 40 kPaper 100 m of pipe length.
Water is flowing at 40L/min in a 2 cm diamter pipe, 10 m long at 20 o C. Calculate whetherthe flow is turbulent or streamline.1 m 3 = 1000 L
1. A research experiment requires a laminar flow of water at 20°C through a 120mm diameterpipe at a Reynolds number of 1992.A. What is the average velocity?B. What maximum velocity is to be expected?C. What would be the pressure drop over a 11m horizontal length of developed flow? Useρ= 1000 kg/m3and v=1x10-6m2/s.D. How long would the entrance region be?
Oil of density 950 kg/m³ and viscosity 1E-2 Pas is to be pumped 10 through a pipeline and the pressure drop must not exceed 2E5 Pa. What is the minimum diameter of pipe which will be suitable, if a flowrate of 50 tonne/h is to be maintained? Assume the pipe wall to be smooth. A. 0.025 mB. 0.175 mC. 0.855 mD. 0.008 m
What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?
A 4in ductile iron pipe carries 0.20 ft3/s of glycerin (SG=1.26) at 100°F. Is the flow laminar or turbulent? Explain.
The pipe fl ow in Fig. is driven by pressurized air inthe tank. What gage pressure p1 is needed to provide a 208Cwater flow rate Q = 60 m3/h?
A 1/4” inside diameter pipe is used to transport SAE 30 motor oil (µ = 0.006266 slug/ft-s and ρ =1.7267 slug/ft3) over a distance of 100 ft. Assuming that the pipe is horizontal and the flow throughit is steady, laminar, and fully-developed, what gauge pressure must a pump develop at the head ofthe pipe to provide a flow rate of sufficient to fill a quart bottle every 5 seconds? [6291 psi] Whatis the Reynolds number (based on diameter) for this flow? [112.5] Is the assumption of laminar flowreasonable?
A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V = 6.6 ft/s. Estimate the proper pipe length (in feet) that will match these conditions. For water at 68°F: ρ = 1.94 slug/(ft^3), and μ = 2.09E-5 slug/(ft-s). Assume also that the head added by pump matches the head loss. Round your answer to 2 decimal places.
A 4-in-ductile iron pipe carries 0.20 ft/s of glycerin (sg = 1.26) at 100°F. Is the flow laminar or turbulent?
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.