A piston cylinder assembly contains water. Heat is transferred to the cylinder in order to heat the water. The atmospheric pressure is equal to 100 kPa. Determine the boiling temperature of water if the mass of the piston is equal to 180000 g. Consider g= 10 m/s^2. The cross sectional area of the piston is equal to 100 cm^2. Select one: a. 131.1 C b. 129.1 C C. 125 C d. 134.1 C

A piston cylinder assembly contains water. Heat is transferred to the cylinder in order to heat the water. The atmospheric pressure is equal to 100 kPa. Determine the boiling temperature of water if the mass of the piston is equal to 180000 g. Consider g= 10 m/s^2. The cross sectional area of the piston is equal to 100 cm^2. Select one: a. 131.1 C b. 129.1 C C. 125 C d. 134.1 C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.11P

See similar textbooks

Similar questions

2.23- Water is at 20 °C and the pressure is lowered until boiling is observed. What is the pressure? from Engineering fluid mechanics 11th
The liquids are positioned as shown in an open tank with a square bottom figure bellow. Solve for the following if the “P atm = 101.325 kPa”.
An air-cooled condenser has an expected U value of 30 W/m2∙K based on the airside. The condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required airside area in m2? Round your answer to 2 decimal places.
Is it true or false? if false please justify/defend your answer. > Chlorine gas at 45 ̊C is under a pressure of 480 kPa. Assume a gas constant of 117 N-m/kg-K. Its specific volume is 0.87. > A 5-mm diameter tube is inserted in mercury and later in water. Assuming the tube is clean so that its angle of contact with mercury is 140 ̊ and the surface tension is 0.5140 N/m, the amount of depression is -2.36 mm.
What is the specific internal energy of water at 50°C with a specific enthalpy of 1500 kJ/kg? Report your answer to one decimal place using rounding.
What is the pressure on a pure water surface if it starts to boil at a temperature of 110C. (Answer 1777.2mb)Show every step
18 - A cylindrical tank with a diameter of 20 cm and a height of 50 cm was filled with water to a height of 30 cm. If the tank is rotated about the vertical axis of symmetry at a constant speed of 21 rad/s, what will be the pressure difference between the bottom center and bottom edge of the tank? a) 1750 Pa B) 1045 Pa NS) 3327 Pa D) 2205 Pa TO) 1125 Pa
As2...Suppose that we could increase the atmospheric pressure on the surface of Mars to 0.2 bar, by vaporizing the polar caps and subsurface ice. This atmosphere would then likely decrease over time, as a result of several processes, such as escape into space, and erosion by the solar wind. How would the surface pressure decrease as a function of time? How much time would it take until the pressure is only 0.1 bar?
nOn 23 January 1960, Jacques Piccard (son of the boat's designer Auguste Piccard) and US Navy Lieutenant Don Walsh achieved the goal of Project Nekton. nThe Trieste is a Swiss-designed, Italian-built deep-diving research bathyscaphe, reached a record maximum depth of 35,797 ft, in the deepest known part of the Earth's oceans, the Challenger Deep, in the Mariana Trench near Guam in the Pacific Ocean. Taking the density of seawater as 64 lbm/ft3, find the sea pressure in psig at the dive depth
Henry's constant for air at 25 C is ____orders of magnitude higher than hydrogen sulfide
Define the conservation of mass.
The vapor pressure of water above water in a capillary is 99.9% of that above flat water surgace at 80°C. What is the diameter of the capillary? density of water= 0.9718g/cm^3, surface tension of water=62.6mN/m