A power source which is rotating at a constant speed of 500 rpm produces a variable torque as shown in Figure Q3. The maximum speed fluctuation is limited to 15%. Determine the following:- (i) (ii) (iii) The mean torque, Tm, hence the power of the source, Pi. The mass moment of inertia of the flywheel, I. The radius of the flywheel to be fitted to the system, if the material density is 6,000 kg/m3 and the ratio of radius to thickness is 3. T (Nm) 180 120 40 t (sec) - 20 Figure Q3

A power source which is rotating at a constant speed of 500 rpm produces a variable torque as shown in Figure Q3. The maximum speed fluctuation is limited to 15%. Determine the following:- (i) (ii) (iii) The mean torque, Tm, hence the power of the source, Pi. The mass moment of inertia of the flywheel, I. The radius of the flywheel to be fitted to the system, if the material density is 6,000 kg/m3 and the ratio of radius to thickness is 3. T (Nm) 180 120 40 t (sec) - 20 Figure Q3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

calculate the power transmitted and the rotational speed in r/min of the small pulley of a belt drive where the diameter of the deriven pulley is 275 mm and rotates at 750 r/min. the driving pulley size is 125 mm. the tension is the tight side of the belt is 500 N, with the tension ratio between the tight and slack side side being 4.33:1
The motion of a pointer over a scale is resisted by a viscous damping torque of magnitude 4 N-m at an angular velocity of 2 rad / s. The pointer, of negligible inertia, is mounted on the end of a relatively flexible shaft of stiffness 2 N-m / rad, and this shaft is driven through a 1 to 4 reduction gear box Determine the overall transfer function of the system If the input shaft to the gear box is suddenly rotated through 1 completed revolution, determine the time taken by the pointer to reach a position within 1 percent of its final value
MECHANICAL VIBRATIONS The system shown in Fig. P3.3 consists of a uniform rod which has length 1, mass m, and mass moment of inertia about its mass center 1. The rod is supported by two springs which have stiffness coefficients ky and k2, as shown in the figure. Determine the system differential equation of motion for small oscillations. Determine also the system natural frequency.
Suppose an automobile engine can produce 195 N⋅m of torque, and assume this car is suspended so that the wheels can turn freely. Each wheel acts like a 14 kg disk that has a 0.195 m radius. The tires act like 2.15-kg rings that have inside radii of 0.18 m and outside radii of 0.34 m. The tread of each tire acts like a 8.5-kg hoop of radius 0.335 m. The 16-kg axle acts like a solid cylinder that has a 1.75-cm radius. The 29.5-kg drive shaft acts like a solid cylinder that has a 3.25-cm radius. Calculate the angular acceleration, in radians per squared second, produced by the motor if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car.
A spring-mass system is shown in the following figure. Use m=3.5 kg and k=100 N/m. a. Determine the static deflection δst . Insert your answer in meters correct up to at least a third decimal place. b. Determine the system period τ. Insert your answer in seconds correct up to at least a third decimal place. c. Determine the maximum velocity vmax which results if the cylinder is displaced 140mm downward from its equilibrium position and released from rest. Insert your answer in m/s correct up to at least a third decimal place.
An engine has a turning moment diagram with the areas above and below the mean torque line of -50 mm2, +120 mm2, -100 mm2, +150 mm2,-80 mm2, +70 mm2 and -110 mm2 with the turning moment diagram scales being for the torque 1mm = 100 Nm and for the crank angle 1mm = 2 °. What is the smallest mass a flywheel of radius of gyration 250mm can have, when running at 600 rpm, if the total fluctuation of speed is not to exceed 2% of the means
A motor capable of producing a constant torque of 100 Nm, and a maximum rotation speed of 180 rads is connected to a flywheel with rotational inertia 0.11 kgm^2. What angular acceleration will the flywheel experience as the motor is switched on?
A flywheel with a moment of inertia of J=1.8 kg*m^2 is on the output ( low speed side ) of a reduction gear with a 3:1 speed ratio. What is the equivalent moment of inertia on the input. ( high speed side ) of the gear if the the gear adds no additional moment of inertia?
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
In the figure below Atwood’s machine is drawn - two masses  and  hanging over a massive pulley of rotational inertia  and radius , connected by a massless unstretchable string. The string rolls on the pulley without slipping.a) Find the acceleration of the system and the tensions in the string on both sides of the pulley in terms of in terms of given variables.b) Why are the rope tensions on two sides of the pulley not the same? Explain it physically.c) Suppose mass    and the system is released from rest with the masses at equal heights. When mass  has descended a distance , find the velocity of each mass and the angular velocity of the pulley.[4***] A string is rolled around a cylinder(   kg) as shown in figure. A person pulls on the string, causing the cylinder to roll without slipping along the floor
A flywheel is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the speed varies from 6 % above the mean to 2 % below it and the fluctuation energy is 1200 kN-cm, If the radius of gyration is 20 cm, find (i) mass moment of inertia of the wheel and (ii) mass of flywheel. The mass moment of Inertia in Kgm2 is Mass of the flywheel in kg is