A series ohmmeter is made up of the following components: supply voltage EB = 3 V, series resistor R, = 30 kO, meter shunt resistor R2 = 50 0, meter FSD= 5() PA, and meter resistance Rm=50 Q. Determine the resistance measured at 0, 0.25, 0.5, and 0.75 of full-scale deflection.

A series ohmmeter is made up of the following components: supply voltage EB = 3 V, series resistor R, = 30 kO, meter shunt resistor R2 = 50 0, meter FSD= 5() PA, and meter resistance Rm=50 Q. Determine the resistance measured at 0, 0.25, 0.5, and 0.75 of full-scale deflection.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter4: Electric Meters

Section: Chapter Questions

Problem 18RQ

See similar textbooks

Related questions

Q: R1 = 100 S2, 1.0 ks2, 10 kS 2, 100 ks2, 1.0 MS2, or 10 MS2, 1% 1/4W D1 = 1N34A, 1N4148 DMM1 (+) R1 +…

Q: A slide-wire potentiometer has a battery of 4 Volt and negligible internal resistance. The…

Q: Two wires A & B made from two different materials have temperature coefficient of resistance equal…

A: GIVEN: αA=0.0025Ω/°CαB=0.0005Ω/°CRT=1200ΩαT=0.001Ω/°C FIND: length of wire A

Q: The output of a potentiometer is measured by a voltmeter having a resistance Rm, as shown in the…

Q: Q2/Design an Ayrton shunt by indirect method to provide an ammeter with current ranges 6A, 25A, and…

Q: The output of a potentiometer is measured by a voltmeter having a resistance Rm, as shown in the…

Q: PMMC type meter has a full scale deflection of 10 mA. The resistance of the coil is 30 ohm So,…

Q: For the circuit in figure #2, explain how it works and how JFET works on it.

A: We are given the following figure :

Q: A DC voltmeter of 1A is to be measured. An ammeter with f.s.d current Im =2 mA and internal…

Q: Q4\ Design a multi range D.C. ammeter by using indirect method to give the following ranges IA, 5A,…

A: Design a multi range DC ammeter. For range of 1A, 5A, 25A, 50A and 100A. If PMMC meter have…

Q: Two wires A &B made from two different materials have temperature coefficient of resistance equal to…

A: Two wires A &B made from two different materials have temperature coefficient of resistance…

Q: An ideal voltmeter connected across terminal A and B of Fig.2 in will read – volt. *

Q: Group 1 Q1) Design with drawing a multi range Ammeter (direct method) for the range 50mA, 100mA and…

A: In this question , we have to design multi range ammeter or increasing range of galvanometer by…

Q: Sketch the following particulars for the device which is used in high voltage and high current…

Q: Integrate 5-stage voltmeter, 5-stage ammeter and 3-stage ohmmeter

A: consider the given question;

Q: R= 2.2k D1 R vo Input Voltage = Vi = 120 Vrms 60HZ vs Output Voltage = 6.3 Vrms Diodes = 1N4001 vs…

Q: A PMMC instrument has internal resistance of 0.66 k2 and gives full scale deflection for 30 mA. The…

Q: Determine the sensitivity of a voltmeter which requires 1 mA of current to produce full-scale…

A: Given Current required to produce full scale deflection Ifsd = 1mA

Q: Figure 1(b) shows the schematic diagram of a potentiometer for the measurement of displacement. i)…

Q: 1. Resistance Measurement Choose a 10% (or a 5% tolerance if you don't have a 10%) tolerance…

A: Standard resistance available in market in between 20 and 45 Ohm is 20R 22R 27R 33R 36R 39R 43R 47R

Q: Q2: A PMMC(Galvanometer instrument) has a resistance of 1002 and FSD for a current of 400Aµ. A shunt…

Q: In a potentiometer, If the slider decreases with a control knob, the resistance of the potentiometer…

A: Potentiometer is an instrument that is used for the comparison of electro motive force. The slider…

Q: Q3:- Determine the minimum input voltage required for regulation to be established in Figure 1.…

A: determine the minimum input voltage required for regulation to be established in figure 1 .assume…

Q: Q2/ D'Arsnoval moving coil meter that modified to measure AC current with full wave rectifier, if…

Q: Q31 A- A series type ohmmeter, show in figure below uses a 500 basic movement requiring a full-scale…

A: Given Rh =2000 Ω Rm =50 Ω V=3 V Ifsd =1 mA

Q: = 100 N and Ifsd = 0.1 mA. Assuming idea in full - scale meter deflection with 9V ac

A: The permanent magnet types of instrument are used to measure the DC value of any wave form. It won't…

Q: With neat diagram, State the principle of RTD sensor…

A: We need to find out resistance at given temperature and we need to find out the tempreture for given…

Q: Q3:- Determine the minimum input voltage required for regulation to be established in Figure 1.…

A: Given data: VZ=13 VR=560 Ω

Q: I need to calculate VG,VS,VD,ID, and voltage out of the following circuit, the component is 2N5485…

Q: Q3 ) a heater with 10 resistance (constant with temperature) if it is used with a half wave…

Q: 4. Explian the working of linear potentiometer with neat circuit diagram.

A: What is a basic Potentiometer- A potentiometer (sometimes spelled pot or pot-meter) is a…

Q: A PMMC instrument has internal resistance of 0.66 kn and gives full scale deflection for 30 mA. The…

A: To use voltmeter as a multi range voltmeter we have to add series resistor.

Q: Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in…

A: Since the same characteristics of the solar panel are connected in series, The output voltage will…

Q: Q3) A. If you get two resistances in the laboratory, one of them high and the second low value , How…

A: NOTE: Since you have posted multiple independent questions in the same request, We will solve the…

Q: The power usage of a DC strip heater is to be determined at a 95% confidence level, using a…

A: The given data's are, The confidence level is 95%, Nominal value of E=8 V, R=5 ohm.…

Q: 1. For each of the circuits in Figure 1, express each labelled voltage and current (e.g., vr, iz) in…

Q: QI. Describe A- Dual-slope digital voltmeter. B- Electrical Standards.

A: A. DUAL SLOPE DIGITAL VOLTMETER The double incline incorporating type DVM coordinates the…

Q: A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The…

A: Required Resistance Rse=Rm(VVm-1) Given: Rm=0.8 K ohm Im= 33 mA V=75 V

Q: Figure Q3(c) shows a Permanent Magnet Moving Coil (PMMC) meter with full scale deflection current of…

A: For the given arrangement of PMMC meter in DC ohmmeter circuit shown below, the full-scale…

Q: Q3: A Series Ohmmeter is made up of the following components: supply voltage Eb=3V, series resistor…

A: Given information about a series ohmmeter is, Supply emf Eb=3 Volts. Series resistance R1=30 kΩ.…

Q: A slide-wire potentiometer has a battery of 4 Volt and negligible internal resistance. The…

A: An sliding wire potentiometer is used to provide current to the sliding wire , the current through…

Q: A rectifier voltmeter uses a full wave rectifier. The meter has an internal resistance of 50 N and…

Q: 1. Consider a half-wave rectifier circuit of Fig 5 with a resistive load of 25 Nand a 60 Hz ac…

Q: Design a multi range DC voltmeter for the range of (0-5) V, (0-10) V, (0-50) V using a basic…

A: Given, Rm=100 Ω IFSD=1 mA where, Rm is the internal resistance and IFSD is the full scale deflection…

Q: Q3/ A- Design an aryton shunt for a meter movement with internal resistance equal to 250002 and full…

A: In this question, We need to design the shunt meter to measure the different different current…

Q: Q5/A- Design a series- type ohmmeter, consist of movement requires 0.5mA for full scale deflection…

A: Given: Full scale deflection current, IFSD=0.5 mAInternal resistance, Rm=50ΩVoltage, E=V=3VRh=3000Ω…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

A series ohmmeter is made up of the following components: supply voltage EB
= 3 V, series resistor R, = 30 kO, meter shunt resistor R2 = 50 0, meter FSD=
5() PA, and meter resistance Rm= 50 Q. Determine the resistance measured at
0, 0.25, 0.5, and 0.75 of full-scale deflection.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The power usage of a DC strip heater can be determined in either of two ways: (1) Heater resist- ance and voltage drop can be measured simulta- neously and power computed, or (2) heater voltage drop and current can be measured simultaneously and power computed. Instrument manufacturer specifications are listed (assume 95% level): Ohmmeter: - 1 Ω = Resolution, 0.5% =Uncertainty (% reading) Ammeter: 0:5 A = Resolution, 1% =Uncertainty (% reading) Voltmeter: 1 V = Resolution, 0.5%=Uncertainty (% reading)
a) With neat diagram, State the principle of RTD sensor b) A platinum resistance thermometer has a resistance of 100 ohm at 250C. The Resistance temperature coefficient of platinum is 0.00392 ohm/ohm0C. (i) Find its resistance at 500C (ii) Let the thermometer has a resistance of 200 ohm, calculate the value of temperature.
PROCESS INSTRUMENTATION AND CONTROL 3. a) With neat diagram, State the principle of RTD sensor b) A platinum resistance thermometer has a resistance of 100 ohm at 250C. The Resistance temperature coefficient of platinum is 0.00392 ohm/ohm0C. (i) Find its resistance at 600C (ii) Let the thermometer has a resistance of 250 ohm, calculate the value of temperature.
1. A PMMC instrument has internal resistance of 1.7kΩ andgives full scale deflection for 50μA. Calculate the required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage ranges of 10V, 50V and 100V.
Outline five (5) sensors that are commonly used in various application to measure physicalproperties
slide wire potentiometer has 10 wires of 2 m each. With the help of a standard voltage source of 1.045 V, it is standardized by keeping the jockey at 104.5 cm. If the resistance of potentiometer wires is 2000 Ω, then the value of working current is?
The power usage of a DC strip heater can be determined in either of two ways: (1) Heater resist- ance and voltage drop can be measured simulta- neously and power computed, or (2) heater voltage drop and current can be measured simultaneously and power computed. Instrument manufacturer specifications are listed (assume 95% level): Ohmmeter: - 1 Ω = Resolution, 0.5% =Uncertainty (% reading) Ammeter: 0:5 A = Resolution, 1% =Uncertainty (% reading) Voltmeter: 1 V = Resolution, 0.5%=Uncertainty (% reading) For loads of 10 W, 1 kW, and 10 kW, determine the best method based on an appropriate uncertainty analysis. Assume nominal values as necessary for resistance, current, and voltage.
The power usage of a DC strip heater is to be determined at a 95% confidence level, using a voltmeter and ohmmeter (P =E2/R). Determine the design state uncertainty of power, using a nominal vale of E = 8v and R = 5 ohm. Instrument Error (95%) Resolution Voltmeter +- 0.5% 0.01 [V] Ohmmeter +- 0.3% 0.001 [ohm]
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00
Answer the following questions: A 0 -150 volt DC voltmeter has a resistance of 100 ohms per volt. What is the instrument resistance? What is the instrument full-scale current? Extend the range of the voltmeter to 750 volts by adding an external multiplier. What is the resistance value, in ohms, of this external multiplier? What is the power dissipation of the external multiplier when the voltmeter is used to measure 750 volts?
Integrate 5-stage voltmeter, 5-stage ammeter and 3-stage ohmmeter
Choose the correct option. 1) Semiconductor materials havea) Positive temperature coefficientb) Negative temperature coefficientc) Unpolar temperature coefficientd) has both negative and positive coefficient but depends upon the conditions 2) The temperature coefficient is a a) Device temperatureb) Rise and fall of a temperaturec) Conductivity of a deviced) Rise and fall of conductivity with temperature 3) Electronic and Electrical devices area) Different in nature, principle, weight and power consumptionb) Electronics is a subfield of Electricalc) Works at different voltage levelsd) All of the above 4) Zener diode conducts ina) Forward regionb) Reverse regionc) Both forward and reverse regionsd) None of the above 5) Multisim is a simulation software that has a code for each electrical device it has.a) Trueb) False 6) A solar panel is also the application of a diodea) Trueb) False 7) Forward biasing causes current which is due to thea) minority carriesb) majority carriersc) Both…