Answered: Q3 ) a heater with 10 resistance…

Q3 ) a heater with 10 resistance (constant with temperature) if it is used with a half wave rectifier , the input voltage source is (V=240v) calculate at a = 6. a) Vde b) Vorms c) Pout

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Related questions

Q: The process in which the amount, quantity and degree r capacity physical parameter are comparison…

Q: Q3) The half-wave rectifier shown below is operating at a frequency of 60 Hz, and the rms value of…

Q: 3) For the Half-Wave Rectifier circuit shown below, determine: the Transformer Turns ratio, n [ IEEE…

Q: Figure Q6 shows the basic circuit for a Silicon Controlled Rectifier (SCR). Question 6 IĻoad V gate…

A: In this answer we will try to find all the required parameters one by one as shown below.

Q: Q4) An experimental ac Voltmeter uses the following circuit , where the PMMC movement has Rm = 100 2…

A: PMMC Voltmeter The permanent magnet moving coil type voltmeter is a voltage measuring instrument…

Q: 4. If we exchange the analog voltmeter used above with a digital voltmeter by setting a digital…

A: Given

Q: A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the output…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The process in which the amount, quantity and degree or capacity physical parameter are comparison…

Q: Draw the circuit diagram of DC power supply of 12 V output by using Full wave rectifier center tap…

Q: Q3. Design a full wave rectifier voltmeter with PMMC instrument parameter are given in Q2 . The ac…

A: Q3. Given: A full-wave rectifier voltmeter with PMMC instrument having parameters: Rm=1.7 kΩFSD of…

Q: A thyristor used in a half wave rectifier used 220V , with firing angle 60°, total resistance load…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: An intrinsic semiconductor is neither a good conductor nor a good insulator. Select one: True O…

Q: O A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the…

A: Note: We have solved the questions first part (a) for firing angle of 45 degree

Q: A conductor carries a current that may be regarded as equivalent to the sum of two components, one…

A: Alternating Currents (AC) are converted to Direct Currents (DC) using rectifier circuits. Two types…

Q: E 16 V de o 12 V ac 60 Hz D R1 10 kN D R2 :10 µF SCR D2 + o Amplifier output 1 kM | 12-V bulb R3 C3…

A: Working Principle of SCR- SCR stands for the silicon controlled rectifier. It is a unidirectional…

Q: The adjacent controlled rectifier has the following parameters: R = 5.20, L = ∞ and a firing delay…

A: Given information about a three phase half-wave rectifier is, Per phase r.m.s. value of input AC…

Q: A single-phase single-pulse diode rectifier (Fig. 3.1), with a resistive load (R=100 n), is fed from…

Q: A Full-wave rectifier circuit uses two silicon diodes with a forward resistance of 202 each. A de…

A: The solution can be achieved as follows.

Q: A battery of em.f 4V and prternal. xesistance 2.n is joined to a desistor of 82 calculate the…

A: Given, A battery of EMF 4 V and internal resistance 2 Ω is joined to a resistor 8 Ω,

Q: Design a full-wave rectifier circuit to rectify an ac voltage of 50 mVp-p. Illustrate its operation.

Q: The is the construction of the available n- and p-type materials, that was constructed as our first…

A: 1)Diode 2) Reverse bias

Q: 3. Consider a semiconductor that is uniformly doped with Na N. 0, with an applied electric field of…

A: Given thatNd=1014cm-3Na=0E=100V/cmμn=1000cm-2/V-sμp=0Nc=2×1019T/30032cm-3Nv=1019T/30032cm-3Eg=1.1eV

Q: Q3: For the circuit shown in Figure 2, find the following: 1. Describe the function of the circuit…

Q: 2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75…

A: GIVEN DATA:

Q: The self heating capacity of a Pt100 temperature element is given as 50mW/Celsius. What is self…

Q: Q7. Discuss the following: 1. Intrinsic Semiconductor 2. Thermal Equilibrium 3. Valence Electron 4.…

A: Semiconductors are a type of materials with conductivity range between the conductors and…

Q: A PMMC instrument with FSD of 50 µA and Rm = 1700 N is used in the half wave rectifier voltmeter…

A: We need to find RS and RSH For given half wave voltmeter.

Q: I-V Characteristics For a NMOS, sketch a I, vs. V ps plot. Label all regions and conditions…

Q: 3. At a certain temperature, the velocity of electrons in an intrinsic silicon material is 120m/s.…

Q: A full-bridge rectifier is supplied from a 220V AC source and operated at firing angle (a,)=60°.…

Q: O A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the…

A: We are authorized to answer one question at a time, since you have not mentioned which question…

Q: Q4) A single-phase controlled rectifier bridge consists of two SCR and two diodes as shown in Fig 1.…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: A three-phase full-wave rectifier as shown in Fig. 1 is connected to a purely resistive load R = 15…

Q: a) A controlled full wave rectifier shown in Fig. 4 (a) below, is fed from 240V, 50 Hz supply which…

Q: Shown below is a rectifier circuit. What is the output DC voltage (in Volts) of this circuit if Vs =…

A: The solution is given below

Q: R V, (o1) = V m sin(œx) Since R = 10, L = 3 mH, Vs = 100sin(2n50t) and a = 120o in the following…

A: Considering the load current is constant. Evaluating the output voltage of the single phase…

Q: Q1: For the circuit shown below, assuming V, = 10V: 1. Calculate the current in the diode (Ip). 1 k2…

Q: (a). Consider a Full Wave Rectifier Circuit with given values as shown. Would you expect the Circuit…

A: Need to find if circuit is fall or not

Q: We have all undoubtedly experienced a loss of electrical power in our office or our home. When this…

Q: During output power measurement DC gives a deflection whereas AC gives proper output. Why? Explain…

A: It is known that DC power is the multiple of voltage and current. and measurement of DC power…

Q: The silicon transistor shown in the figure below has reverse saturation current of 10-° A. If VBE =…

A: Given circuit is - Given values are - Reverse saturation currentIS=10-9AVT=26mVη=2VBE=0.7Volt

Q: A sinusoidal voltage of 50 V (Vrms) and frequency 50 Hz is applied to a half wave rectifier. RL =…

A: Dear student please find the attachment.

Q: Circuit 2 Full wave Rectifier with Center Tapped Transformer D1 Vs- 12Vac Vo R-k S) Vs= 12Vac D2 a.…

Q: A PMMC instrument with FSD of 100 µA and a coil resistance of 1 kQ is to be converted into a…

Q: 3phase half wave rectifier ,the line voltage(460v).load resistance(R=202).find Vdc, Vrms, PIV, RF,…

A: 3 phase half wave rectifier, The line voltage given 460V Load resistance R= 20 ohm Find the…

Q: A conductor carries a current that maybe regarded as equivalent tò the sum of p components, one of…

A: Introduction: Direct current flows in one direction only, which means that its terminals are…

Q: Please explain simply in detail, why Analog and Digital Electronics are important. Also please…

A: Electronic devices and their applications, are now a major part of our life. These embedded circuits…

Q: A sinusoidal voltage of 50 V (Vrms) and frequency 50 Hz is applied to a half wave rectifier. RL =…

A: Dear student please find the attachment.

Question

Q3 ) a heater with 10 resistance (constant with temperature) if it is used with a
half wave rectifier , the input voltage source is (V=240v) calculate at a =
6
a) Vde
b) Vorms
c) P.
out

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is CEMF?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75 µA. If the meter coil resistance is 900 Q and the multiplier resistor is 708 k2, calculate the applied rms voltmeter when the voltmeter indicates FSD.
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.Use Silicon diodes.
Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
During output power measurement DC gives a deflection whereas AC gives properoutput. Why? Explain it. (Voltmeter, Ammeter and Isolator Connection of a Simple Half Wave Rectifier Circuit.)
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.
Design a full-wave rectifier circuit to rectify an ac voltage of 50 mVp-p. Illustrate its operation.
A sinusoidal voltage of 50 V (Vrms) and frequency 50 Hz is applied to ahalf wave rectifier. RL = 200 Ω, RF = 20 Ω (diode internal resistance of diode). Find Vdc, Idc, Imax, Irms, Pdc,efficiency and ripple factor.
Design the network of below to maintain V L at 12 V for a load variation (I L) from 0 mA to 200 mA. That is, determine R S and V Z. Determine P Z max for the Zener diode of part (a).
While constructing a Bridge rectifier, the designer mistakenly has swapped the terminals of D3 as shown in the figure below, where • Diode D3 is damaged so that it is always open circuit regardless of the applied voltage. • vs(t) is a sinusoidal signal with a peak value (Vs = 5 V). • Diodes are modelled using the constant voltage model with VDO = 0.7 V • The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hz • The resistance RL = 10 kohm. a) Calculate the transformer turns ratio (N1/N2) if vs(t) is obtained from the secondary side of the transformer whose primary side is connected to the ac line voltage (which has a 120 V rms value). b) Plot in the same graph the input signal vs(t) and the output signal vout(t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms values of the output signal vout(t). (hint: sin2 (x) = 0.5(1- cos(2x))) d) If a capacitor C = 3.58 µF is connected across R = 10 kohm, repeat (b) in a new graph e) With the…