Answered: A shaft is used to transmit 67 kw at a…

A shaft is used to transmit 67 kw at a speed of 2,281 rev/min. Using a maximum allowable shear stress of 57 M shaft diameter in mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating…

A: Given data d=30mm P=50kw N=2100rpm τ=230MPa. To find 1) τmax…

Q: A motor driving a soiid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of…

A: Given data as per question Power transmitted =40KW Speed =500 rpm Diameter of We know that Power…

Q: A steel propeller for a windmill transmits 8.1 kW at 63.4 rpm. If the allowable shear stress in the…

A: To find : The minimum diameter required for a solid shaft . Given : The power is P=8.1KW The speed…

Q: 2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the…

Q: Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60…

Q: A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside…

A: Given data Power transmitted = 45 kW Speed (N) = 500 rpm Inside dia (d) = 0.6*outside dia(D)…

Q: A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the…

A: Given Data⇒ Line shaft rotating at (N)=320 rpm Power transmitted (P)=35 KW Allowable shear stress…

Q: A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 290 lb-ft and Tp= 100 lb-ft,…

Q: A solid shaft transmits 30 kW at 3 rev/s. Determine the cubic diameter of the shaft (d3 ),if the…

Q: A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of…

Q: Problem 4

Q: * While transmitting power ofa steam turbine, the angle of twist of a rotating shaft was measured…

A: Given: · Angle of twist of a rotating shaft ∴ θ = 1.2° = 1.2×π180 =…

Q: Example1: A solid shaft in a rolling mill transmits 20 kW at 120 r.p.m. Determine the diameter of…

A: The above question is based on Torsion of solid shaft.

Q: Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1…

Q: A solid shaft is to transmit 22kW at 110 rpm. Determine the diameter of the shaft if the shearing…

Q: The working conditions to be satisfied by a shaft transmitting power are (a) that the shaft must not…

A: GivenG=80000 N/mm2T=1MWattN=240rpmθlim=1oL=15dσallow=55 N/mm2

Q: a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the…

A: Given Data⇒ Hollow shaft Maximum torque : Tmax=4750 N-m Shear stress in shaft : ζ=50 Mpaζ=50×106Pa…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: Q2: A solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW…

Q: Question: A solid shaft is transmitting 1 MW at 240 r.p.m. Determine the diameter of the shaft if…

A: Given data: P=1 MWN=240 rpmTmax=1.2Tmτmax=60 MPa Need to determine the diameter of the shaft.

Q: A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of…

A: Given: The speed of the shaft, N = 200 rpm The power transmitted, P = 20 kW The allowable shear…

Q: 78. A motor driving a soiid circular steel shaft transmits 40 kW of power at 500 rpm. If the…

A: Given, Power transmitted by shaft = P = 40 kW = 40000 W Rotational speed of shaft = N = 500 rpm…

Q: A steel marine propeller shaft 13 inches in diameter and 15 ft long is used to transmit 9,426 hp at…

A: GIVEN DATA- D=13in L=15ft P=9426hp N=189rpm G=12*10^6 psi WE HAVE TO FIND SHEAR STRESS

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.…

A: Given data: Maximum torque, T = 4750 N·m. Shear stress in the shaft, τ = 50 MPa. The ratio of…

Q: A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear…

Q: Calculate the unit shearing stress at the inner surface of a hollow shaft which D = 150 mm and d =…

Q: A solid shaft is transmitting 1 MW at 250 r.p.m. Determine the diameter of the shaft if the maximum…

A: As per our guidelines we have to answer one question only so, post the question separately and…

Q: A Compound Steel (G=80GPA) Shaft consists of a solid 90mm diameter (segment1) and a solid 70mm…

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750…

A: Given Data⇒ Hollow shaft Maximum torque : T=4750 N-m Ratio of inside to outside diameter is :…

Q: A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not…

Q: (6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed…

Q: ubular shaft, having an inner diameter of mm and an outer diameter of 40 mm, is be used to transmit…

Q: A solid shaft is to transmits 22 kW at 110 rpm. Determine the diameter of the shaft if the shearing…

A: Given data as per question Power transmitted =22kw Speed =110 rpm hearing stress =35 Mpa The angle…

Q: (6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed…

Q: A 2-in-diameter steel shaft rotates at 240 rpm. If the shearing stress is limited to 12 ksi,…

A: Diameter, D= 2 in Speed, N= 240 rpm= 24060 rps Shearing stress, τ= 12 ksi= 12(1000) lbf/in2= 12000…

Q: 4) Shafts with lengths 5m and4 m are connected by gears. The diameter and shear modulus for both…

A: Given, Shaft lengths , 4m and 5m. Diameter of the shafts , d= 10cm Shear modulus of the shaft ,…

Q: A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the minimum…

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800…

Q: Q4. Determine the diameter of a shaft which is transmitting 60KW at 200rev/min, for: 1- Solid shaft…

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

Q: 2) The minimum outer diameter required for a hollow shaft if the shaft inner stress of tallow= 75…

Q: While transmitting power of a steam turbine, the angle of twist of a rotating shaft was measured and…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: A hollow circular shaft is required to transmit 300 metric horsepower at 200 r.p.m. The maximum…

A: Given data

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m…

A: Given data Maximum torque (T) = 4750 N-m limited shear stress (τ) = 50 MPa Inside dia to outside…

Q: A 3-m steel shaft is to transmit 100 kW at 300 rpm. It carries two gears each weighing 1.9 kN…

Q: A solid shaft is transmitting 1MW at 240rpm . Determine the diameter of the shaft if the maximum…

Q: Determine the diameters of a hollow shaf

Q: Q3) A ship's propeller shaft has external and internal diameters of 25 cm and 15 cm. What power can…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A shaft is used to transmit 67 kw at a speed of 2,281 rev/min. Using a maximum allowable shear stress of 57 MPa, find the
shaft diameter in mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear stress of 48 MPa, find the shaft diameter in mm
A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2
A shaft is transmitting 100 kW at 160 rpm. Find a suitable diameter for the shaft if the maximum torque transmitted exceed the mean by 25%. Take maximum allowable shear stress as 70 MPa.
Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.
A hollow circular shaft has an outer diameter of 100 mm and a wall thickness of 25 mm. The allowable shear stress in the shaft is 125 MPa. Find the maximum torque that the shaft can transmit.
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the maximum shear stress in the shaft
find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft transmits 150 KW power at 150 RPM.