Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.

Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

A circular steel shaft of diameter 30 mm is subjected to a torque of 60 N-m. Calculate the angle of twist if the length of the shaft is 20 m.
A 39 in. tubular shaft is in torsion under a torque of 34 lb-in.. Its cross-section shown below as diameter d1 = 3.2 in., diameter d2 = 1.4 in. If it is a soft tube, and G = 315 psi, calculate the angle of twist of the shaft: _____ O (degrees). Pay attention to units, and calculate your answer to one decimal place.
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
Determine the allowable torque a hollow steel shaft can transmit if the outside diameter is 4 inches, and the inside diameter is 3 inches. The allowable shear stress is 10,000 psi. Compute the angle of twist per foot of length. Answer = 85,900 in-lbs I'm unsure of how to solve this problem. Could you please help me solve for the answer step-by-step? Thank you in advance.
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
The outside diameter of a hollow shaft is 1.6 times the inside diameter. When transmitting 420 W of power at 180 rpm, the angle of twist is one degree over a length of 40 times the inside diameter. Taking G for the material as 85 GN/m^2, determine the outside diameter of the hollow shaft in mm.
Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000 in-lb. The maximum shear stress developed in the shaft is not to exceed 8,000 psi. The inside diameter is to be 2/3 of the outside diameter. Calculate the angle of twist in degrees for a 14 foot length of this shaft. Answer: D(outside) = 9.259 inches, D(inside) = 6.176 inches, angle of twist= 1.39 degrees I'm unsure of how to solve this problem. Could someone help me walk through the process step-by-step? Thanks in advance.
The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
Compute the torsional shear stress in a circular shaftwith a diameter of 50 mm that is subjected to a torqueof 800 Nm
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the angle of twist in degrees
A solid circular shaft is subjected to a torque of 21,334 in-lb. Calculate the diameter required if the allowable twist is 1.7° per foot, and the material is steel alloy which has a modulus of rigidity of 12,000,000 psi.
what horsepower can be transmitted by 1/2 in. diameter solid shaft at 1800 rpm if the allowable torsional shearing stress is 6000 psi?