A shearing Machine requires 150kg-m of energy to shear a steel sheet and has a normal speed of 3rev/sec, slowing down to 2.8rev/sec during the shearing process. The flywheel has a mean diameter of 75cm and weighs 0.018 kg/cm³. The width of the rim is 30cm. If the hub and arms of the flywheel account for 15% of its total weight, find the thickness of the rim. Note: Thickness unit should be in cm

A shearing Machine requires 150kg-m of energy to shear a steel sheet and has a normal speed of 3rev/sec, slowing down to 2.8rev/sec during the shearing process. The flywheel has a mean diameter of 75cm and weighs 0.018 kg/cm³. The width of the rim is 30cm. If the hub and arms of the flywheel account for 15% of its total weight, find the thickness of the rim. Note: Thickness unit should be in cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Does the shear flow vary parabolically along with segments that are inclined?
A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
Answer is: V = 14.17 ft/s
Water enters the piping arrangement shown in the figure at a volumetric flow rate Q1=0.4 m^3/s. The water flow is then divided into pipes of diameter [Theta2] = 5 cm and [Theta3]= 10 cm. If the average speed of the water in pipe 2 is [V2] = 25 m/s. What is the flow rate Q3 in m^3/s in the pipe of diameter theta 3? And at what speed does the fluid leave through pipe 3 in m/s?
An axial fan having a hub diameter of 0.4 m and a hub ratio of 0.5 delivers a flow rate of 5 m3/s at a rotational speed of 1800 rpm. If the chord length at mean radius is 0.12 m, determine the pressure change across the fan using this formula
1. A diverging pipe has diameter of 20cm and 30cm respectively at section 1 and section 2. If the velocity of water at section-1 is 5 m/s, determine the discharge through this pipe. Determine the velocity at section-2. 2. A 50cm diameter pipe, conveying water, branches into two pipes of diameter 30cm and 20 cm respectively. If the average velocity in the 50 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in 20 cm pipe if the average velocity in 30 cm diameter pipe is 1.5 m/s.
How long should a rotor blade of a wind turbine be if it is designed to produce 10 kW and the prevailing wind speed is about 50 kph? Assume that air density is 1.20 kg/m3.
The diameter of the ball is 30 cm as shown in the figure. Calculate the river current velocity [m/s]. (NOTE: Neglect the weight of the cable. SGBALL = 0,20 PWATER = 1000 KG/M3 CD,BALL=0,12
A 5-m self-propelled combine makes an average stop of 4 min every time its 2-ton grain tank is to be unloaded. Gross yield of the 20-ha field is 42 tons. The operating speed is 4.8 kph. The time for turning on the headland at the ends of the 500-m field is 15 seconds.Find the actual field capacity:a. 1.5 ha/hr b. 2.5 ha/hrc. 2.0 ha/hr c. 3.0 ha/hr
The velocity distribution in the boundary layer is given by :u/U=(y/δ)^0.23 where u is the velocity at a distance y from the plate and u=U at y=δ , δ being boundary layer thickness. Find: a-The displacement thickness .b- the momentum thickness .c- the energy thickness. d- Boundary layer shape factor .e- energy loss due boundary layer if a particular section. The boundary layer thickness is 28mm and the free stream velocity is 19 m/s. if the discharge through the boundary layer region is 8m3/s per meter width, express this energy loss in term of meters of head. Take ρ=1.2 kg/m3