A simply supported beam carries a distributed load of 10 kN/m over a span of 5 m and a concentrated load of 10 kN at pint A and 8 kN at pint D, as shown in the figure below. Determine: 1. The Shearing Force and Bending Moment Diagrams for Fig. (a). 2. The maximum bending stress set-up on the beam. The beam section is shown in Fig (b). 10 kN 8 kN 20 mm 20 mm 20 mm 10 kN/m A D B C 0000 1m 40 mm' 1 m 3 m 20 mm 20 mm (а) (b)

A simply supported beam carries a distributed load of 10 kN/m over a span of 5 m and a concentrated load of 10 kN at pint A and 8 kN at pint D, as shown in the figure below. Determine: 1. The Shearing Force and Bending Moment Diagrams for Fig. (a). 2. The maximum bending stress set-up on the beam. The beam section is shown in Fig (b). 10 kN 8 kN 20 mm 20 mm 20 mm 10 kN/m A D B C 0000 1m 40 mm' 1 m 3 m 20 mm 20 mm (а) (b)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.11P: A wood beam AB on simple supports with span length equal to 10 ft is subjected to a uniform load of...

See similar textbooks

Similar questions

The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C. The loads consist of a horizontal force P1= 4,0 kN acting at the end of a vertical arm and a vertical force P2= 8.0 kN acting at the end of the overhang, Determine the shear force Fand bending moment M at a cross section located 3,0 m from the left-hand support. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations, Find the value of load A that results in V = 0 at a cross section located 2.0 m from the left-hand support. If P2= 8.0 kN, find the value of load P1that results in M = 0 at a cross section located 2,0 m from the left-hand support.
A wood beam AB on simple supports with span length equal to 10 ft is subjected to a uniform load of intensity 125 lb/ft acting along the entire length of the beam, a concentrated load of magnitude 7500 lb acting at a point 3 ft from the right-hand support, and a moment at A of 18,500 ft-lb (sec figure). The allowable stresses in bending and shear, respectively, are 2250 psi and 160 psi. From the table in Appendix G, select the lightest beam that will support the loads (disregard the weight of the beam). Taking into account the weight of the beam (weight density = 35 lb/ft3), verify that the selected beam is satisfactory, or if it is not, select a new beam.
A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A where they enter the ground and they are supported by horizontal struts whose center lines are 10 m above A. The piles are spaced 1 m apart between centers and the depth of water against the dam is 10 m. Assuming that the thrust in the strut is two-sevenths the total water pressure resisted by each pile, sketch the form of the bending moment and shearing force diagrams for a pile. Determine the magnitude of the bending moment at A and the position of the section which is free from bending moment. (Cambridge). i. 238 kN-m; 0.75 m from A. ii. 238 kN-m; 0.75 m from B.
The simple beam AB, shown below, supports a concentrated load of 6 kN and a segmentof non-uniform load of intensity varies from 1 kN/m to 3 kN/m at point B. a). Determine the maximum bending stress and the maximum shear stress acting on the beam if the beam has a rectangular cross section of (500 mm × 200 mm).
A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed3.25 N/mm2 find the load w.
6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and a uniformly distributed load of 400 N/m over a span from its free end to a point 0.5 m from the free end. Neglecting the mass of the beam itself, draw the shear force and bending moment diagrams for the beam. Show all calculations as well
A beam 8.5-m long is fixed at the left end and supported by a roller at a point 1.5-m from the right end. There is an internal hinge at a point 2.5m from the fixed end. The beam is loaded by a clockwise couple equal to 50 kN-m acting at a point 1-m to the right of the fixed end, a downward concentrated vertical load equal to 12- kN acting at a point 4.5-m to the right of the fixed end and a downward uniform vertical load equal to 5-kN/m starting at a point 4.5m from the fixed end up to the right end of the beam. Draw the shear and moment diagram of the beam .
A metal beam with span L =3 ft is simply supported at points A and B. The uniform load on the beam (including its own weight) is q =160 lb/in. The cross section of the beam is rectangular with width b =1 in. and height h =4 in. The beam is adequately supported against sideways buckling. Determine the bending stress in the top and bottom of the beam and maximum shear stress at the neutral axis
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
The simple beam AB, shown below, supports a concentrated load of 22 kN and a segment of anon-uniform load varying from 20 kN/m at point C to 40 kN/m at point B.1. Calculate the maximum bending stress and the maximum shear stress acting on the beam if ithas a rectangular cross section (500 mm × 200 mm) as shown below.
The beam shown in the figure is supported by a pin at point A and a roller at point D. Draw the diagrams of shear force and moment, through cuts in the beam, determine the previously requested. The exercise is in the attached image.
To calculate torsional deformation and shear stress due to an applied force in a door handle design. A locked door handle is composed of a solid circular shaft AB with a diameter of b = 120 mm and a flat plate BC with a force P = 67 N applied at point C as shown. Let c = 462 mm , d = 134 mm mm , and e = 158 mm. (Treat the handle as if it were a cantilever beam.) If the maximum allowable shear stress is τallow 145 MPa , determine the maximum force P that can be applied to the door handle. (Recall that piece AB is now a hollow tube.)