A simply supported beam of length “L” is subjected to linearly varying load distribution. The magnitude of the left end of the linearly varying load distribution is Zero and the magnitude of the right end of the linearly varying load distribution is Q. Draw the shear force diagram (SFD) and bending moment diagram (BMD) over the span length and also find the magnitude of maximum bending moment and its position.

A simply supported beam of length “L” is subjected to linearly varying load distribution. The magnitude of the left end of the linearly varying load distribution is Zero and the magnitude of the right end of the linearly varying load distribution is Q. Draw the shear force diagram (SFD) and bending moment diagram (BMD) over the span length and also find the magnitude of maximum bending moment and its position.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Related questions

Q: Plot the shear and moment diagrams for the beam loaded with both the distributed load and the…

A: The SFD and BMD is shown below;

Q: A 5 m long beam (Fig. 1) is rigidly built in at the left end and simply supported at the right end.…

A: If such end of the ruler is laying on the desk and is being held down, the ruler will bend if a…

Q: is subjected to a point load of

A: Required support reaction in cantilever beam Where F = 5kN

Q: Derive the expression for the maximum deflection of a simply supported beam of negligible weight…

Q: A 8-kN load is supported by a cart that rolls along a beam as shown in Fig. Plot Mmax, the maximum…

A: Consider the diagram shown below for the given beam. Take moment about the point A. From the…

Q: A uniformly distributed force of C kN/m and a concentrated load of D kN are applied to a cantilever…

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force…

Q: The variation of bending moment of a beam with distance x from one end is given by M(x) = 1-x2 .Then…

A: The slope of the bending moment diagram at a cross-section is equal to the magnitude of the shear…

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

A: given; lets take reaction at A=RAweight density (w)=12KN/mmoment at C (MC)=5KNmAB=1mBC=0.5mCD=0.5m

Q: Q1: For the beam Shown in Figure 1 16kN 4kN/m 4kN/m B 3m 2m 2m 3m Figure 1 I. Find the reaction at…

Q: Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for a loaded simply supported…

A: Given point loads are 1KN & 4KN Uniformly distributed load 2 KN/m To Find Shear Force and…

Q: Figure 1a shows a simply supported beam, AB of length L = 5.6 m, with a uniform distributed load of…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 800 mm.…

A: Answer: The largest moment M that can be applied to the beam is 494.6 N•m.

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

Q: Hey, please reply as soon as posible Make the shear force and bending moment diagrams on Beam…

Q: Construct a shearing force(Q) and a bending moment(M) diagrams.

A: Given data To determine Shear force and bending moment diagram

Q: Rod (2) Bar (2) is simplified into a simple beam with a load in the middle of the rod. a. Draw a…

Q: The Reactions are Given. Draw the Shear and Moment Diagrams and deflection diagram

A: Consider a section at a distance of x from the left end of the beam. For a section AB of the beam,…

Q: A simply supported beam of length 5m, carries a uniformly distributed load of 12019080kN/m extending…

Q: For the hanger shown in Figure P5.15, determine the change in slope of the hanger at point B,…

Q: A cantilever 10 m long caries two concentrated loads, one at the free end and the other at the…

Q: Draw (FBD) and calculate the support reactions in the simply support beam ABCD below 3kN 5kN bo 60°…

Q: A cantilever beam AB with a built-in restraint at end A is subjected to a combination of loads as…

Q: A simply supported beam supports a triangular distributed load as shown. The peak load at the right…

Q: Example 2: Write shear and moment equations for the beams in the following problem. Let x be the…

Q: A built-in cantilever beam with a hollow rectangular cross-section is subjected to a uniformly…

A: Boundary conditions will use in beam problem to find the integration constant while finding…

Q: (a) Figure 6 shows a beam of length 8 m, simply supported at each end, and loaded with a point load…

A: Given dataLength of the beam L = 8mPoint load P = 60kNUniformly distributed load UDL = 30kN/mLength…

Q: For the simply supported beam subjected to the loads shown. Let a=3.00 m, b=4.00 m, PB = 30kN, and…

A: Given data: ◆ The values of point loads applied on the beam: PB = 30 kN , Pc = 65 kN ◆ The length of…

Q: 200 kN/m 140 kN I (m) 5 10 7.5 Figure.2: Encastré beam under variety of loads Your tasks are as…

Q: Find the section modulus for a beam of circular cross section with the diameter of 70mm. The section…

Q: For the structural beam loaded and supported as shown in Figure 2, (a) Draw a free body diagram and…

A: This question is related to the topic of mechanics of the solid. now reactions are the support used…

Q: N for Newton, m for meter, mm for millimeter, N/(mm^2) for Stress, mm^2 or m^2 for Area, mm^4…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

Q: QS\ Draw shear force and bending moment diagram for the beam shown below 10kN/m 4m 3m

A: Draw the schematic diagram of the beam.

Q: A steel beam ABC carries a uniformly distributed load of w (kN/m) over the unsupported length BC, as…

Q: For the simply supported beam subjected to the loads shown. Let a=3.00 m, b=4.00 m, PB = 30kN, and…

Q: Two orientations of a 1 m length cantilever beam are to be considered as shown in Figure Q2(a). The…

Q: A cantilever beam of length 5m is loaded at the free end with a point load. The bending moment at…

A: Given data: The length of the beam is L = 5 m. The bending moment at the fixed end is M = 2.5 kN-m.…

Q: For a loaded cantilever beam of uniform cross section, the bending moment along the length is M(x) =…

A: Given data: - The equation of the bending moment is Mx = 5x2 + 10x. The distance where the…

Q: Analyze the given beam that is subjected to a bending moment of 20 kg-m. Find the maximum stress…

A: An I section with unequal top and bottom width is given. And the bending moment acting on the beam…

Q: Let's consider a simple supported beam subjected to a triangular distributed load and a couple…

A: Answer is M(x) = -83.3 X3 - 166.7 X ( N.m)

Q: For a cantilever beam subjected to a vertical force at its free end, how many elements should be…

A: To find :- How many element should be used for exact solution.

Q: The simply supported beam in Figure 3. carries two concentrated loads. Sketch the shear force and…

A: From the moment equilibrium about the point A, From the vertical equilibrium of forces,

Q: Q: Draw shear force and bending moment diagrams for the beam shown below and then find max. shear…

Q: A uniform thin-walled beam of constant wall thickness t has a cross- section in the shape of an…

Q: Let's consider a fixed supported beam subjected to a triangular distributed load as shown in the…

Q: Draw the shear force and bending moment diagram for a cantilever beam subjected to uniformly…

Q: Draw the Shear Force Diagram (SFD) and Bending Diagram (BMD) for a loaded simply supported beam…

A: Consider the free body diagram of the beam as shown below. From the moment equilibrium about the…

Q: Draw the Shear Force and Bending Moment diagrams stating the important values

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Draw the shear force diagram (SFD) and bending moment diagram (BMD) over the span length and also find the magnitude of maximum bending moment and its position.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending moment acting on section 1 in terms of the distance x (0 < x< L). [Note: Case 1 results in the conventional V- and M-diagrams, in which the loads are fixed and the location of the section varies; the diagrams for Case 2 (called influence diagrams) show the variation of V and M at a fixed section as the location of the load is varied]
Draw the shear force and bending moment diagrams of the given simple headstock beam? can you solve it step by step!
The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero at the left end to 360 lb/ft at the right end. In addition, a 1000-lb upward vertical load acts at the free end of the beam. (1) Derive the shear force and bending moment equations, and (2) draw the shear force and bending moment diagrams. Neglect the weight of the beam
Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for a loaded simply supported beam shown below. 1KN 4KN
Draw the shear force diagram and bending moment diagram for the beam and loading shown in picture below.
A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.
c) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. Label the diagrams properly and provide values at all key points within the diagrams.