A small spherical ball having diameter of d= 20 cm and at temperature of 150 °C is placed in a water bath maintained at 20 °C to be cooled down. Consider the proportionality constant to be a= 0.005/m²-s. a) Determine the time required for the temperature of the ball to reach 40 °C. b) At what time the temperature of the ball reach to 20 °C? c) What's the final temperature of the ball? Bulk environmental temperature=T, T(t) Initial solid temperature, T Surface area, A

A small spherical ball having diameter of d= 20 cm and at temperature of 150 °C is placed in a water bath maintained at 20 °C to be cooled down. Consider the proportionality constant to be a= 0.005/m²-s. a) Determine the time required for the temperature of the ball to reach 40 °C. b) At what time the temperature of the ball reach to 20 °C? c) What's the final temperature of the ball? Bulk environmental temperature=T, T(t) Initial solid temperature, T Surface area, A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30
A ship with vertical sides near the water line, weighs 40 MN and draws 6.7 m in salt water (specific gravity = 1.026). Discharge of 2 MN of water ballast decreases the draft to 6.4 m. What would be the draft d of the ship in fresh water?
A vessel cylindrical in shape and closed at the top and bottom is 200 mm in diameter and 0.15 m in height. The vessel is completely filled with water. If it is rotated about its vertical axis with a speed of 200 r.p.m., what is the total pressure force (in N) exerted by water at bottom of the vessel? CHOICES: a.7.09 b.10.35 c.80.6 d.34.4
A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m3. (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind turbine?
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
The farmer wanted to know the number of hills per hectare in his rice production, if row is 15 cm apart and the hills is 15 cm apart.
6.4. A force of 300 N is sufficient to keep a 100-kg wooden crate moving at constant velocity across a wooden floor. What is the coefficient of kinetic friction?
3. Given two potential windfarm sites with the following conditions, find the expected wind powerdensity available (per square meter) for each location.a. Site red: sea-level elevation, 10 m/s average wind speed, average temperature 25°Cb. Site blue: 1000-meter elevation, 12 m/s average wind speed, average temperature 20°C
1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
A dam has been built to hold back a lake. The dam gate is at the same depth as the lake bottom. The center of the rectangular gate is at some depth d below the water surface. The gate is 1 m tall and 3 m wide. If the average force applied to the gate by the water is 744 kPa m^2, what is d? Show your work. (a) 15 m (b) 150 m (c) 3000 m (d) 30 m (e) None of the above.
Don't skip steps. Show the complete solution for this problem. A golden breast plate weighing 18.63 kg Is dropped in a tub that Initially contains water. After the breast plate was totally submerged. the water level rises by 61.87 cm. The tub has a diameter of 6 centimeters and the breast plate was said to be made only from gold and silver Compute for the percentage of each component of the breast plate if the density of gold Is 19.3 g/cubic centimeter and silver has a density of 10.49 g/cubic centimeter.
Step by step process of solution.