A solid circular rod of diameter d undergoes a bending moment M=1300 lbf-in inducing a stress o=32 M/(?), Using a material strength of 25 kpsi and a design factor of 2.5, determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.

A solid circular rod of diameter d undergoes a bending moment M=1300 lbf-in inducing a stress o=32 M/(?), Using a material strength of 25 kpsi and a design factor of 2.5, determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.21P: A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular...

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A pinned-end strut of a length L = 5.2 ft is constructed of steel pipe (E = 30 × 103 ksi) having an inside diameter d1= 2.0 in. and outside diameter d2= 2.2 in. (sec figure). A compressive load F = 2.0 kips is applied with eccentricity e = 1.0 in. What is the maximum compressive stress max in the strut? What is the allowable load Pallowif a factor of safety n = 2 with respect to yielding is required? (Assume that the yield stress y of the steel is 42 ksi.)
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety