Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is 300 mm and the number of pulley arms are 4. The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are 600 N and 200 N respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is 300 mm and the number of pulley arms are 4. The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are 600 N and 200 N respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
Q8 A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters ofthe contacting surfaces are 200 and 250 mm respectively. The coeffi cient of friction is 0.1 and themaximum pressure between the contacting surfaces is limited to 0.4 N/mm. Assuming uniform weartheory, calculate the required force to engage the clutch and the power transmitting capacity at 720rpm.
A v-belt drive is to transmit 330kW power from a pulley of 1m diameter running at 250rpm. The safe pull in each belt is 800N and the mass of the belt is 0.46kg per meter length. The angle of lap and the groove angle is 160º and 45ºrespectively. If the coefficient of friction between the belt and the pulley is 0.3. Calculate the number of belts required
1. A pulley 580 mm in diameter transmits 60 kW at 650 1pm by means of belt. Determine the effective belt pull.2. Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if pulley diameters are 9 in and 18 m, respectively.
A V-belt drive transmits 20kW from an electric motor running at 1440rpm to the main shaft of a roving machine. The motor and main shaft pulleys have 300 & 600 rpm respectively. The coefficient of friction between belt and pulley is 0.25. The centre distance between the shafts is 1000mm. The top width, thickness, section angle and density of belt and permissible tension on the belt are 22mm, 14mm and 40deg, 0.97gcm-2 and 600N respectively. How many belts are needed? Calculate the length of a belt needed
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 448 N to 975 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.
A thin rod 5 mm diameter is held between two chucks 0.8 m apart and deflects 0.5 mm under its static weight. The rod weighs 1.508 N/m and the flexural stifness is 6.136N-m^2. Calculate the lowest critical speed in rpm taking into account the distributed mass.
Starting with a spring index of C = 10, design a compression coil spring of 302 stainless wire with squared ends. The spring deflects 50 mm when a force of 90 N is applied and closes to solid when ys is 60 mm. At closure, use a design factor of 1.2 guarding against yielding. Select the smallest diameter wire where wire diameters are available in 0.2-mm increments between 0.2 and 3.2 mm. For the design, specify the wire diameter, the inside and outside diameters of the coil, the spring rate, the total number of coils, the free length of the spring, the final factor of safety, and stability conditions.
3.A chain drive using bush roller chain transmits 5.6 kW of power. The driving shaft on an electric motor runs at 1440 r.p.m. and velocity ratio is 5. The centre distance of the drive is restricted to 550 ± 2% mm and allowable pressure on the pivot joint is not to exceed 10 N/mm2. The drive is required to operate continuously with periodic lubrication and driven machine is such that load can be regarded as fairly constant with jerk and impact. Design the chain drive by calculating leading dimensions, number of teeth on the sprocket and specify the breaking strength of the chain. Assume a factor of
Determine the principal dimensions of a cone clutch faced with leather to transmit 55 kW at 1100 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume : semi-angle of the cone = 15; μ = 0.2; mean diameter of cone = 6 to 10 d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm2; load factor = 1.75 and mean diameter to face width ratio = 6.