Please read the question carefully to answer all requirements (a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loadedat the tip with a transverse force of 1000 lbf and an axial force of 5000 lbf, as shown in thefigure. Study the significance of the transverse shear stress in combination with tension andbending by calculating magnitudes of the stresses. Explain and comment on the stresses andstrains generated.1000 lbfB1 in dia.Cross section at the wall5000 Ibf

A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 Ibf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated.

A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 Ibf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.9P: A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial...

See similar textbooks

Similar questions

A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
A W 360 x 79 steel beam is fixed at A. The beam has a length of 2.5 m and is subjected to a linearly varying distributed load with maximum intensity q0= 500 N/m on segment AB and a uniformly distributed load of intensity qQon segment EC. Calculate the state of plane stress at point D located 220 mm below the top of the beam and 0\3 m to the left of point B. Find the principal normal stresses and the maximum shear stress at D. Include the weight of the beam, See Table F-l(b), Appendix F, for beam properties.
Two steel tubes are joined at B by four pins (dp= 11 mm), as shown in the cross section a—a in the fiaure. The outer diameters of the tubes are dAB= 41 mm and dBC= 28 mm. The wall thickness are tAB= 6.5 mm and tBC= 7.5 mm. The yield stress in tension for the steel is sy = 200 MPa and the ultimate stress in tension is ??U:= 340 MPa. The corresponding yield and ultimate values in shear for the pm are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing R between the pins and the tubes are 260 MPa, and 450 MPa, respectively. Assume that the factors safety with respect to yield stress and ultimate stress are 3.5 and 4.5. respectively. (a) Calculate the allowable tensile force P allowconsidering tension in the tube (b) Recompute P allowfor shear in the pins.(c)Finaly, recomputed Pallowfor bearing between the pm and the tubes. Which is the tubes. Which is the controlling value value of P?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).