A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top surface. Given the shear constant for steel as 8.3 x 1010 N/m2, compute the shear angle. 4.4 x10-7 rad 1.4 x 10-7 rad 3.4 x 107 rad 2.4 x 10-7 rad none of these

A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top surface. Given the shear constant for steel as 8.3 x 1010 N/m2, compute the shear angle. 4.4 x10-7 rad 1.4 x 10-7 rad 3.4 x 107 rad 2.4 x 10-7 rad none of these

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter5: Further Applications Of Newton's Laws: Friction, Drag, And Elasticity

Section: Chapter Questions

Problem 38PE: A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear...

See similar textbooks

Related questions

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

Q: In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The…

A: Diameter=21mm=0.021m Width=110mm=0.110m Bearing stress=110mpa Shear stress=61mpa

Q: A horizontal aluminum rod 2.9 cm in diameter projects 7.2 cm from a wall. A 950 kg object is…

Q: By applying 2.00 x 106 N/m2 shear stress to a steel bar 2 m in length, calculated the shear bending…

A: Shear Bending Stress(S) for steel is given as, S=(8.3×108 N/m2)=Shear StressShear strain

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: A bar with a uniform cross-sectional area of 300 mm² is subjected to axial loads, as shown in the…

A: Correct option (b) 140 Mpa

Q: NORMAL STRAIN 1. A concrete has a height of 5 meters and has unit area of 3 m² supports a weight of…

Q: A solid steel shaft will not twist through more than 3° in a 6.0 m length when subjected to a torque…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A: To find minimum diameter for each rod use the formula of normal stress and put the values to solve .…

Q: The following figures show a steel bars of thickness h = 5 mm. the bars are subjected to a force P.…

A: Given: Figures with thickness, h = 5 mm Shear stress, t = 140MPa

Q: An aluminum (ρ = 2.7 g/cm3) wire is suspended from the ceiling and hangs vertically. How long must…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear…

A: Given

Q: Is thrée times larger than in steel shaft. QI1) For the section shown aside, if the bending stress…

Q: A horizontal aluminum rod 3.6 cm in diameter projects 5.6 cm from a wall. A 1000 kg object is…

A: Given:- A horizontal aluminum rod of diameter d = 3.6 cm = 0.036 m The distance from the wall is L…

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

A: Length , L = 4 m Cross sectional area , A = 9.3 x 10-3 m2 Load , F = 7.5 x 104 N Young's modulus ,…

Q: A 26.0 m long steel cable with a cross-sectional area of 2.05 ✕ 10−3 m2 is used to suspend a 3.60 ✕…

Q: a diver stands (80kg) at the end of a diving board, causing the board to dip 10cm. The board has a…

Q: When using a pencil eraser, you exert a downward force of 5.5 N at a distance of 1.9 cm from the…

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

A: Given: Length of each beam, L=4 m Area of cross-section,A=7.5×10-3 m2 Load, W=4.5×104 N Young's…

Q: Determine the strain if a rod is experiencing a stress of 70,000 kPa with a modulus of elasticity of…

A: Given: The stress is 70000 kPa. The modulus of elasticity is 175 GPa.

Q: A horizontal aluminum rod 4.7 cm in diameter projects 4.4 cm from a wall. A 1100 kg object is…

A: Given: Diameter of aluminum rod, d=4.7 cm projects at a distance L= 4.4 cm from a wall. Mass of…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than 1.50 x…

A: Given : Young's modulus for bone, Y = 1.50*1010 N/m2 Stress to break the bone, S =…

Q: 'One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…

Q: Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What…

A: Given, Diameter of the metal bar, d = 6.0 mm = 6.0 × 10–3 mRadius, r = d/2 = 2.5 × 10-3 m Maximum…

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

Q: Nylon breaks when the tensile stress within it reaches 1.0 x 10 ’ Pa. Which range below includes the…

A: Given data: The stress in thread is σ=1×109 Pa. The diameter of thread is d=1.00 mm.

Q: Consider a steel bolt as a cylinder with a diameter of 3.41 cm and length of 13.8 cm. A shear or…

A: diameter of 3.41 cm length of 13.8 cm shear stress of 313 MN/m ² shear Modulus Ssteel =G= 8.4×…

Q: An elevator of mass of 1200kg is hanged by steel wire with a cross sectional area 1.2*10-4 m2…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: (a) Write the given data. σ=320 106 N/m2ε=0.0040

Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 10-4 m2 is subjected to a tensile…

A: Given- Length L= 115 m Cross-sectional area A= 1.13 x 10-4 m2 Tensile force F= 565 N

Q: A compressive force of 3.1 × 10ª N is exerted on the end of a 23-cm-long bone of cross-sectional…

A: applied compressive force(F) = 31000 N Cross sectional area of bone = 3.7 cm 2 = 0.00037 m2…

Q: A 50-N force is applied to a metal rod with a length of 10 m and a cross-sectional area of 1.0 x…

Q: When a tensile load (F) is applied to a solid homogeneous rod, the rod undergoes a change in length…

A: Required : Alternate expression for the strain energy.

Q: "One end of a steel rod of radius R = 10mm and length L = 80 cm is held in a vise. A force of…

Q: What force is required to stretch a steel wire 1 cm² in cross section to double its length, if…

A: When a force is applied at the end of the material gets deformed and the molecules of the material…

Q: Find the mass of the picture hanging from a steel nail as shown, given that the nail bends only 1.80…

A: The force applied perpendicular to the L0 and parallel to the cross sectional area A can be…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: Young's modulus is a measurement of a material's capacity to endure length changes when subjected to…

Q: A horizontal aluminum rod 3.4 cm in diameter projects 7.0 cm from a wall. A 810 kg object is…

A: Answer:- Given Shear modulus (G) = 3 × 1010 N/m2 Length (L) = 7 cm =7× 10-2 m Diameter of rod (d)…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: The pole in the figure is a a 90° bend in a power line and is therefore subjected to more shear…

A: Tension in wires at top , T = 3.5 x 104 N Angle made by wire with the vertical , θ = 80° Height of…

Q: The femur bone in a human leg has a minimum effective cross section of 3.15 cm2. How much…

A: The pressure presently working on an object can be defined as the physical force that is being…

Q: Find the elongation of a steel rod of 100 mm long when it is subjected to a tensile strain of 0.004?…

A: (b) 0.4 mm

Q: The figure represents an insect caught at the midpoint of a spider-web thread. The thread breaks…

A: When the thread is stretched under the weight of the insect, calculate the total length of the…

Q: A vertical steel girder with a crosssectional area of 0.15 m2 has a 1550 kg sign hanging from its…

Q: Two strips of metal are riveted together at their ends by four rivets, each of diameter 8.0 mm. What…

A: Diameter of each rivet,

Q: The figure shows an approximate plot of stress versus strain for a spider-web thread, out to the…

A: Solution:-

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the
top surface. Given the shear constant for steel as 8.3 x 1010 N/m2, compute the shear
angle.
4.4 x10-7 rad
1.4 x 10-7 rad
3.4 x 107 rad
2.4 x 10-7 rad
none of these

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Review the relationship between stress and strain. Can you find any similarities between the two quantities?
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?