A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test. different solution please

A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test. different solution please

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the length increases to 150.40mm. The material remains within the linear elastic region and its modulus of elasticity is 200,000 MPa. Determine the force, in Newton (N), applied to the test.
A steel pipe having a length of 3 ft, an outside diameter of 5 in., and a wall thickness of 1/2 in. is subjected to an axial compression of 50,000 lb. Assuming a modulus of elasticity of 30 * 106 psi and a Poisson’s ratio of 0.27, finda. the shortening of the pipe,b. the increase in the outside diameter, andc. the increase in the wall thickness.
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’sratio of 0.35 is subjected to tension within the elastic region. Determine the force that will produce a reduction of 0.003 mm in the diameter.
A metal rod with 0.5 in. diameter is subjected to 2000 lb tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is 10,000,000 psi, Poisson’s ratio is 0.33, and the yield strength is 21,000 psi.
A rectangular block of aluminum 30 mm * 60 mm * 90 mm is placed in a pressure chamber and subjected to a pressure of 100 MPa. If the modulus of elasticity is 70 GPa and Poisson’s ratio is 0.333, what will be the decrease in the longest side of the block, assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the block?
The rectangular block shown in Figure is subjected to tension within the elastic range. The increase in the length of a is 2 * 10-3in. and the contraction of b is 3.25 * 10-4 in. If the original lengths of a and b were 2 in. and 1 in., respectively, what is Poisson’s ratio for the material of the specimen?
A tensile stress is applied along the long axis of a cylindrical steel rod with a diameter of 10 mm. If the deformation is entirely elastic, determine the magnitude of the load required to produce a 5 * 10-3 mm change in diameter.Assume a modulus of elasticity of 200 GPa and a Poisson’s ratio of 0.27.
A tensile stress is applied along the long axis of a cylindrical steel rod with adiameter of 10 mm. If the deformation is entirely elastic, determine the magnitude of the load required to produce a 5 X 10-3 mm change in diameter. Assume a modulus of elasticity of 200 GPa and a Poisson’s ratio of 0.27.