A steel rod is located by using force fit into the body of a mechanical system with a radial interference of 30 um. Considering the static loading in the figure, evaluate the factor of safety employing Von-Mises criteria. Data are as follows: E = 210 GPa, Sy = 510MPA %3D d=40mm 20KN 30 30mm 60mm 50mm

A steel rod is located by using force fit into the body of a mechanical system with a radial interference of 30 um. Considering the static loading in the figure, evaluate the factor of safety employing Von-Mises criteria. Data are as follows: E = 210 GPa, Sy = 510MPA %3D d=40mm 20KN 30 30mm 60mm 50mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.5 cm x 7.5 cm steel beam with a length of 61 cm is subjected to a reversed load of 17.8 kN at midpoint. If yield stress and endurance stress are 410 MPa and 155 MPa respectively, what should be the minimum factor of safety? A helical spring has a free length of 203 mm, outside diameter of 115 mm and a wire diameter of 13 mm. It consist of 9.5 coils squared and grounded at the ends. If it is compressed to its solid length, what is the stress in the spring? Let G = 80 GPa.
Determine the minimum force required to deflect the spring with spring constant of 251 N/mm to a displacement of 5 mm.
A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be driven by vee belts through a pulley. The combined tensions of the belt apply and the weight of the pulley assembly applies a force of 5.4kN and 900N respectively. The shaft has a diameter of 32mm. Bearing A at the top supports the shaft radially whereas bearing B at the bottom supports the shaft axially and radially. Two deep groove ball bearings have been selected for this application. The models of the bearings are SKF 6305 and SKF 6205 for bearing A and B respectively. a) What are the forces at bearing A and B? b) Paste a screenshot of the graph showing the distribution of the forces in the shaft. c) From the report, find the static load capacity for: Bearing A Bearing B
A spring balance is calibrated in an environment at a temperature of 25oC and has the following deflection/load characteristics Load (Kg) 0 2 Deflection(mm) 0 36 It is used in an environment at a temperature of 35oC and the following deflection/ load characteristics. Load (Kg) 0 2 Deflection(mm) 4 50 Determine ZERO DRIFT at 25oC ? ZERO DRIFT at 35oC ? ZERO DRIFT? ZERO DRIFT/oC?
A 300 HP crawler tractor is pulling a wagon of 25 cu yd capacity equipped with highpressure tires. The weights of the crawler tractor and the empty wagon are 25 tonsand 15 tons respectively. The haul road is well maintained and compacted earth.Select highest figure in range for rolling resistance. The coefficient of traction is0.75. Half of the weight of the crawler tractor and half of the weight of the loadedwagon need to be considered in the slippage check. No penetration occurs as thesurface is hard enough. The average temperature and barometric pressure at thesite location are 30oC and 56.00 cm of Hg respectively. The drawbarpull producedby the tractor at standard conditions is given in the machine’s manual as 15,000 kgin first gear. What is the gradability of the tractor/wagon combination if the wagon isloaded with dry earth? Take a gradability safety factor of 85%.
The displayed piece is loaded at 300 N with C in the positive x direction and 200 N in the positive y direction. The diameter of the US bar is 12mm. The part is made of AISI 1040 CD steel. Depending on the error at point A, determine the safety factor by the following methods.(a) maximum shear stress theory.(b) distortion-energy theory.
A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock conditions where Ks= 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axesare parallel and in the horizontal plane. The shafts are 8 ft apart. The 6-in driving pulley rotates at1750 rev/min in such a way that the loose side is on top. The driven pulley is 18 in in diameter. Thecoefficient of friction is 0.8. Analyze the centrifugal tension Fc and the torque T.?
Stress plots for (b) sigma r and theta for both the inner and outer ring. Interface pressure found to be 13.33 kpsi
Compare each strength gain and relate its significance on Strength and Economy. The design strengths are: a.) 290.7 kNm (using 4-25mm dia. Tension bars) b.) 378.7 kNm (using 6-25mm dia. Tension bars) c.) 385.97 kNm (using 9-25mm dia. Tension bars)
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)
a helical compression spring with squared and ground ends is made of shot-peened astm a232 spring wire with presetting(G=79 GPa) . It is used to control a cyclic dynamic load that varies between 562 and 0 N. if a saftey factor of 1.12 is used, determine the allowable shear stress for a design cinsideration of infinite fatigue life
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.