The uniform beam shown below weights 5.0×10²N and supports a 7.0X10²N load. Find the tension in the tie rope and the force of the hinge on the beam. Answer must be in 2 significant figure. 35° 0.40 L 0.60 L F= 2,900N FH=2,000N, 35° below the horizonta 700 N

The uniform beam shown below weights 5.0×10²N and supports a 7.0X10²N load. Find the tension in the tie rope and the force of the hinge on the beam. Answer must be in 2 significant figure. 35° 0.40 L 0.60 L F= 2,900N FH=2,000N, 35° below the horizonta 700 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.7P: A W 8 × 28 beam of a length 10 ft is held between immoveable supports. The beam has a modulus of...

See similar textbooks

Related questions

Q: B/A container which has a volume of 0.1 m' is fitted with a plunger enclosing 0.5 kg of steam at 0.4...

Q: Talks about grinding, and Grinding Lathe Tool Bits. Explain properly.

Q: 6. BONUS PROBLEM (CALCULUS BASED - NON NUMERICAL PROBLEM). Here we are designated to observe a block...

Q: A 600mm by 300mm reducer connects two pipes. The velocity at the exit end of the reducer is 5m/s and...

Q: Consider several pots with equal amounts of boiling water in them. Each pot is heated by an 850°C el...

A: Solution: Given Data:

Q: An aircraft engine produces (1.4800x10^2) kW power in normal idle mode. If the fuel flow rate is (3....

Q: What defines the combustion chamber of afour-stroke engine?

A: Given data : Combustion chamber of four stroke engine.

Q: Determine the tension in the cord and the rate

A: To find Tension in the cord.

Q: Part C Figure < 1 of 1 Determine the shear stress Tzz that acts at point A Express your answer to th...

A: Given data as per question Force in x-direction =1300N Force in y-direction =615N Considering FBD of...

Q: 72. A pipe is connected vertically to the discharge side of a pump. The top of the pipe is a short h...

Q: The rod has a diameter of 40 mm (Figure 1) It is subjected to the force system F, = 1300 N, F, = 615...

Q: The loaded frame shown in Fig. 1, is supported at A (fixed support) and B (roller support). C is an ...

A: a) Reaction at support A and B The free body diagram of the right part of the hinge is here, RB is ...

Q: A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in diameter f...

Q: 2. Compare the propulsive efficiency (7,)F of an ideal turbofan with that of a core jet (i.e., a tur...

A: Solution: Given Data: ν=0.5β=1, 2, 5, 20

Q: CA horizontal pipe narrows from a radius of 0.325 m to 0.150 m. If the speed of the water in the pip...

Q: 2. Work, Energy, Power, and Energy Conservation. In Doctor Stranger Episode 13. A heart surgery was ...

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a mo...

A: Given the relation: Consider the tight side of the pulley as T1 And the loose side of the pulley as ...

Q: Name the three drive configurations that a greatset can transfer torque.

A: Given data : Drive configurations

Q: Two wooden members shown which support a 4kip load, are joined by plywood splices fully glued on the...

A: Given Data The support load is: P=4 kip The ultimate shearing stress is: τu=360 psi The clearance b...

Q: for the cirele below (Reg) sedroh fon 300 150 se RI R43502

Q: Determine the reactions at A and B when: ( a) α-0 (b) a = 75° (c) a = 35°. 75 lb 10 in. 10 in. В a 1...

A: Find the reaction at A and B

Q: 1. A Jet of water 50 mm diameter is discharging under a constant head of 70 meters. Find the force e...

Q: Oil specific gravity of oil = 0.80 1 ft 4 ft Water

Q: . Design vehicles and show its parts. a clutch which is used in most cars and small commercial

A: SINGLE PLATE CLUTCH is most widely used plate in cars and small commercial vehicles, with parts as f...

Q: The horizontal rigid beam ABCD is supportedby vertical bars BE and CF and is loaded byvertical force...

A: Given E = 200 GPa Area, ABE= 11,100 mm2 ACF = 9280 mm2. Find Deflections

Q: Who is right?

A: To Find:- Who is right

Q: 2- As the hydraulic cylinder rotates about 0, the exposed length I of the piston rod P is controlled...

Q: 10-8 2 2 2n 2 PsdS |r-r'l ppdpd 4+p² 30 раpdф V = 49.7 V 10-9 36n 4+p

Q: In a certain machine, a shaft 3 inches in diameter caries a bending moment of 2210 Ib-ft. What torqu...

Q: The velocities of the particles at an instant are VA = 5m/s and VB = 7m/s, with the angle between th...

A: Given data vA = 5 m/svB = 7 m/sAngle between vA and vB = θ = 37.5°

Q: Sclect an appropriate manufacturing process where dimension accuracy and precisions are critical. As...

A: Extreme tolerances are required to ensure proper performance and reliability. In automotive applicat...

Q: determine the value of the force Fi

A: determine the value of the force F

Q: Q7: Convert: A) 2 kmh to m/s and to f/s? B)300 lb.s to N.s and 52 slug/n' to kg/m'?

Q: 3- Find madadeflection Ø Mad bending strest crossasection(150 mm leemny mm 20 kN E=15KN 2u lkN 20KN ...

A: As loading is symmetrical, we can take advantage of that. Reaction forces would be same at both sup...

Q: A college in a metropolitan area wishes to increase its evening offerings of business-r elated! cour...

A: he target market customers for an evening school offering business related courses could either be s...

Q: True or False? In a parallel circuit, circuit current is the same throughout all parts of the circui...

A: Given Data : Parallel circuit

Q: A video of the artist Mariah Carey went viral online purportedly because she was able to twist off t...

Q: This country's population in 2010 will be (Type an integer or decimal rounded to one decimal place a...

A: Find the population of country ( 2010)

Q: (3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank ha...

Q: The cantilever beam AB shown in the figurehas an extension BCD attached to its free end.A force P ac...

Q: PROBLEM 4 To monitor the pressure in three pipes, a manometer setup was installed in one section of ...

A: Given: gauge pressure in pipe B→PB=7200 lbft2 because inside the pipe B, water is flowing and densit...

Q: . Two shafts A and B whose axes are intersecting but inclined to each other at 20° are connected by ...

A: Answer: The maximum torque in shaft B is 1117.55 kN•m.

Q: With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is m...

A: Given: The outside diameter of shell, Ds = 90 cm The shell thickness, t = 8 mm = 0.8 cm The operatin...

Q: What advantage might the commercially packaged coolant material have over ice other than it produces...

A: Advantages that commercially packed coolants have over ice: 1. One of the major disadvantages of usi...

Q: Water at 4.4oC with a density of 1000 kg/ m3 and a viscosity of 1.55 cP is to flow through a horizon...

Q: Determine the distribution of heat flux for the square heated plate In the figure. Use a relaxation ...

A: There is no heat flux distribution in horizontal direction because the temperature of walls are same...

Q: experimental: measurement of electric boiler efficiency 6- Discussion: 1. Sketch a diagram for the e...

A: 100% efficient is called as electric boilers that are the amount of electricity given will in return...

Q: Name three factors that determine the torque produced by an induction motor.

A: Given Data : Torque produced by induction motor

Q: A vertical cylindrical continuous decanter is to separate 44 gal/min of a liquid petroleum oil from ...

A: given data:

Q: A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque ...

Question

I need the answer as soon as possible

The uniform beam shown below weights 5.0x102N and supports a 7.0X102N load. Find the tension in the tie
rope and the force of the hinge on the beam. Answer must be in 2 significant figure.
0.40 L
0.60 L
FT= 2,900N
FH=2,000N, 35° below the horizontal
700 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for a W 250 × 89 steel column having a length L = 10 m. Let E = 200 GPa.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Column AB has a pin support at A,a roller support at B, and is compressed by an axial load P (see figure). The column is a steel W12 × 35 with modulus of elasticity E = 29,000 ksi and proportional limit pl = 50 ksi. The height of the column is L = 12 ft. Find the allowable value of load P assuming a factor of safety n = 2,5.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
A steel bracket of solid circular cross section is subjected to two loads, each of which is P = 4.5 kN at D (see figure). Let the dimension variable be b = 240 mm. Find the minimum permissible diameter dmaxof the bracket if the allowable normal stress is 110 M Pa. Repeat part (a), including the weight of the bracket. The weight density of steel is 77.0 kN/m3.
Two pipe columns (AB, FC) are pin-connected to a rigid beam (BCD), as shown in the figure. Each pipe column has a modulus of E, but heights (L1or L2) and outer diameters (d1or different for each column. Assume the inner diameter of each column is 3/4 of outer diameter. Uniformly distributed downward load q = 2PIL is applied over a distance of 3L/4 along BC, and concentrated load PIA is applied downward at D. (a) Derive a formula for the displacement