A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the total deformation of the bar if it has a modulus of elasticity E = 28.5 x 10^6 psi. O 0.1423 inches O 0.1338 inches O 0.1378 inches O 0.1352 inches O 0.1364 inches

A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the total deformation of the bar if it has a modulus of elasticity E = 28.5 x 10^6 psi. O 0.1423 inches O 0.1338 inches O 0.1378 inches O 0.1352 inches O 0.1364 inches

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A steel bar 106mm long and having a square cross section 20 mm (0.8 in.) on an edge is pulled in tension with a load of 89,000 N, and experiencedan elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of the steel?
A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in tension with a load of 20,000 lbf and experiences an elongation of 0.004 inches. Assuming that the deformation is entirely elastic, calculate the elastic modulus of the steel.
A steel column is 3 mm long and0.4 m in diameter. It carries a loadof 50 MN. Given that the modulusof elasticity is 200 GPa, calculatethe strain.
Actual weight of steel bars = 1.520 kg/m, Standard weight of steel bars (16mm )= 1.579 kg/m, Load at yield point = 3480 kgf ,Load at breaking point = 7540 kgf, Maximum load = 7. 9260 kgf, Unit weight of steel = 7854 kg/m^3. What is the cross-sectional area in m^2? Compute it's yield strength,ultimate strength and breaking strength in MPA?
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
1. A force of 3000 lb stretches a steel rod into its proportional limit of 37 ksi. Calculate the approximate diameter of the steel rod.2. Considering a modulus of elasticity of 30 x 106 psi, calculate the deformation of the 3 ft. long steel rod in number 1.
Which of the following nearly gives the frictional force at the 550lb block? a. 200 lb b. 420 lb c. 320 lb d. 140 lb
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5
Actual weight of steel bars = 2.340 kg/m, Standard weight of steel bars (20mm )= 2.470 kg/m, Load at yield point = 13100 kgf ,Load at breaking point = 14500 kgf, Maximum load = 18200 kgf, Unit weight of steel = 0.2834 lb/in^3. What is the cross-sectional area in ft^2, Yield strength, ultimate strength and breaking strength in psf?
A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.