Actual weight of steel bars = 2.340 kg/m, Standard weight of steel bars (20mm )= 2.470 kg/m, Load at yield point = 13100 kgf ,Load at breaking point = 14500 kgf, Maximum load = 18200 kgf, Unit weight of steel = 0.2834 lb/in^3. What is the cross-sectional area in ft^2, Yield strength, ultimate strength and breaking strength in psf?

Actual weight of steel bars = 2.340 kg/m, Standard weight of steel bars (20mm )= 2.470 kg/m, Load at yield point = 13100 kgf ,Load at breaking point = 14500 kgf, Maximum load = 18200 kgf, Unit weight of steel = 0.2834 lb/in^3. What is the cross-sectional area in ft^2, Yield strength, ultimate strength and breaking strength in psf?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 3CQ

See similar textbooks

Similar questions

Actual weight of steel bars = 1.520 kg/m, Standard weight of steel bars (16mm )= 1.579 kg/m, Load at yield point = 3480 kgf ,Load at breaking point = 7540 kgf, Maximum load = 7. 9260 kgf, Unit weight of steel = 7854 kg/m^3. What is the cross-sectional area in m^2? Compute it's yield strength,ultimate strength and breaking strength in MPA?
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to a tensile load of 3900 lb. What is the modulus of elasticity of this alloy steel? A)29,010 ksi B)27,000 ksi C)30,000 ksi D)28,000 ksi
In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. Determine the dimension b so that the joint is as strong as the boards.____________inches in 2 decimal places.
1. A force of 3000 lb stretches a steel rod into its proportional limit of 37 ksi. Calculate the approximate diameter of the steel rod.2. Considering a modulus of elasticity of 30 x 106 psi, calculate the deformation of the 3 ft. long steel rod in number 1.
Note: Modulus of elasticity of steel is 2.0x106 kg/cm2
What change in volume would a 100 mm cube of steel suffer at a depth of 5 km in sea water? Take E=2.05 x 10 5N/mm2 and N = 0.82 x 10 5N/mm2
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5
A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. * 0.6 in.cross section and a gauge length of 2 in. Under this load, the bar elastically deforms so that the gauge length increases to 2.007 in. and the cross section decreases to 0.599 in. * 0.599 in. Determine the modulus of elasticity and Poisson’s ratio for this metal.
A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. by 0.6 in. cross section and a gauge length of 2 in. Under this load, the bar elastically deforms so that the gauge length increases to 2.007 in. and the cross section decreases to 0.599 in. by 0.599 in. Determine the modulus of elasticity and Poisson’s ratio for this metal *
Determine the maximum tensile strength of the steel bar described by the following data Initial diameter = 12 mm Final diameter = 6.5 mm Initial length = 60 cm Final length = 86 cm Ultimate load = 5000 kgf
SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 4: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of castiron 5 mm thick. Compute the load that will compress the combined bar a total of 1 mm. For steel, E = 200 GPa, and for cast iron, E = 100 GPa.