A steel tube with a circular cross section has an outside diameter of 294 mm and wall thickness of 2 mm. The cylinder is twisted along its length of 2 m with a torque of 54 kN-m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Tr Determine the maximum torsional shear stress using the equation Tmax The maximum torsional shear stress is MPа.

A steel tube with a circular cross section has an outside diameter of 294 mm and wall thickness of 2 mm. The cylinder is twisted along its length of 2 m with a torque of 54 kN-m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Tr Determine the maximum torsional shear stress using the equation Tmax The maximum torsional shear stress is MPа.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
A bar having a radius equal to 0.375 inches is subjected to different torques along its span as shown below. Determine the max shear stress that is experienced by the bar.
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
A thin cylinder 75mm internal diameter, 250 mm long with wall 2.5mm thick is subjected to an internal pressure of 7MN/m^2. Determine the change in internal diameter and the change in length. If additional to the internal pressure, the cylinder is subjected to a torque of 200Nm, find the magnitude and nature of the principal stress set up in the cylinder by using mohr's circle methods. Youngs modulus is 200GN/m^2. And v=0.3
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an outside diameter of 0.51 in. and an allowable shear stress of 4500 psi. Segment (2) is a solid aluminum shaft with an outside diameter of 0.41 in. and an allowable shear stress of 6000 psi. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in lb-in rounded to the nearest tenths.
A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length having an external diameter of 16mm and a wall thickness of 3mm. The rod and tube are rigidly connected at their ends so that they twist together when a torque of 20 Nm is applied. Galuminum = 30GPa; Gbrass = 40GPa. Determine: a) The values of the torsional stiffness for the rod and the tube b) The torque transmitted by each c) The maximum shear stress in each d) The angle of twist
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.