A stepped shaft has maximum diameter 45 mm and minimum diameter 30 mm. The fillet radius is 6 mm. If the shaft is subjected to an axial load of 10 kN, find the maximum stress induced, taking stress concentration into account.

A stepped shaft has maximum diameter 45 mm and minimum diameter 30 mm. The fillet radius is 6 mm. If the shaft is subjected to an axial load of 10 kN, find the maximum stress induced, taking stress concentration into account.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.5P: The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as...

See similar textbooks

Related questions

Q: A column with a wide-flange section has a flange width b = 250 mm , height h = 250 m m, web…

A: Given dataWIdth of the flange w = 250mmHeight of the flange h = 250mmThinkness of the web tw=…

Q: A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the…

A: Power, P = 120 kW Speed, N = 200 rpm Tmax = 1.2Tmean Shear stress, = 70 N/mm2…

Q: A stepped shaft has maximum diameter 45 mm and minimum diameter 30 mm. The fillet radius is 6 mm. If…

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A: Given data:

Q: Steel tube shaft having length 3mm and diameter 50mm subjected to axial compressive force 55 k N and…

A: Given Data: Steel tube having length (l)=3 mm…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

Q: d Bronze B Steel - b–

Q: 3. A round shaft, 45 mm in diameter, carries a 3500 N load, as shown in the Figure. If the shaft is…

Q: The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The…

A: Given data: P=200 hpN=3500 rpmG=12×106 psiτ=12000 psi Need to determine the diameter of the smallest…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

Q: Q2: A solid steel shaft 450 mm long is stressed at 75 MPa when twisted through 3° and used to…

Q: A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear…

A: Given data: The diameter of the shaft is D = 30 mm. The tangential force acting on the shaft is F =…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: The cantilevered tube shown in the following figure is to be made of 2014 aluminum alloy and is…

A: The tube is subjected to axial loading, bending, and torsion simultaneously, thus there will be…

Q: A propeller shaft is required to transmit 45 kW power at 500 r.p.m. It is a hollow shaft, having…

A: Given data: - The power transmitted by the shaft is P = 45 kW. The speed of the shaft is N = 500…

Q: The hollow ship shaft shown in the figure; It transmits 9880 hp and rotates at 3940 rpm. Since the…

Q: A generator shaft in a small hydroelectric plant turns at 120 rpm and delivers 38 kW (see figure).…

A: Torque is the force measure to rotate an item around an axis. The torque can therefore be defined as…

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300…

A: Given that , L=12m =12000mm P=1000 kW =1000×106N-mm/s

Q: .A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: ircular tube of aluminum is subjected to torsion by torques T applied at the ends (see figure). The…

A: Given:L=27 indi=1.2 indo=1.6 inθ=3.157°T=51,662 in

Q: A stepped steel shaft shown below is subjecte to 10 N-m torque. If the moduius of rigidity 80 GPa,…

A: Given:Torque, T=10 N-mG=80 GPad1=50 mmd2=25 mmL=100 mm

Q: A solid shaft BC is fixed at the B end and subjected to torque T at the C end, as shown below. The…

Q: 80 mm 20 mm 7 mm M M Click to see additional instructions Calculate the minimum Safety Factor if the…

Q: In the figure below, A 50 mm shaft is subjected to a reversed load P = + 2700 N. Find the length…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880…

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

Q: A shaft is required to transmit 1 MW power at 240 r.p.m. The shaft must not twist more than 1 degree…

A: Find the diameter of shaft and shear stress in the shaft.

Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 104 N/mm2 and length…

A: Write the expression to determine the powerP transmitted by a shaft. P=2πNT60 Here, speed of the…

Q: A cantilever hollow circular bar 5mm thick with inside diameter of 75mm is subjected to a torque of…

A: Given Data: The thickness of the bar is, t=5 mm. The inside diameter of the bar is, d=75 mm. The…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Given, Diameter of shaft = d = 100 mm Axial stress = σx = 50 MPa = 50 N/mm2 Torque = T = 10 kNm = 10…

Q: A cylindrical steel pressure vessel 200 mm radius with a thickness of 20 mm, is subjected to an…

A: Given: P = 5 MN/m2 t = 20 mm r = 200 mm

Q: The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of…

Q: A 7/8 in. diameter shaft made out of ductile material is used to transmit power from motor. The…

Q: 1. Shaped stepped shaft A torque of Tx = 200 Nm and a moment of Mz = 260 Nm are applied.Calculate…

A: given:torque TX=200Nmmoment MZ=260Nmsmall shaft diameter=150 mmbig shaft diameter=400mmfillit…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A: Given data, σpunching= Average punching shear stress in the collar = 100 MPa σbearing = Average…

Q: A copper column of annular cross section has an outer diameter of 5m and is subjected to an axial…

A: Given Outer diameter of column do=5 m Axial load applied P=200 kN Allowable compressive stress…

Q: 3. A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: Given data: Outside diameter of tube is d0 = 104 mm. Inside diameter of tube is di = 82 mm. The…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

Q: Figure shows a cantilever shaft made of steel subjected to several loading T=5kNm, M=2.5kNm, and…

Q: torsional moment T = 8,019 Nm and a load P = 39,980 N are applied at the same time to a circular…

A: Given data:- Force (p) = 39980 N Torque(T) = 8019 N-m Inner diameter = 38 mm Outer diameter = 90 mm…

Q: A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm.…

Q: A torque of Tx=200Nm and a torque of Mz=260Nm are applied to the stepped shaft in the figure.…

A: Given data as per question Tx=200Nm Torque Mz=260Nm Larger diameter =400 mm Smaller diameter=150 mm…

Q: Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m…

Q: A round shaft of diamater D = 65 mm with a groove cut into it where the diameter decreases to d = 50…

Q: A solid circular shaft is subjected to a bending moment of 2800 Nm and a torque of 10,000 Nm. The…

A: Given Bending moment = 3000 Nm Torque = 100000 Nm Material 45C8 Maximum tensile stress = 700 MPa…

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

A: Write the given data. In section AC,d1=0.75 inL1=6 inIn section CB,d2=1.50 inL2=15 in

Question

A
A stepped shaft has maximum diameter 45 mm and minimum diameter 30
mm. The fillet radius is 6 mm. If the shaft is subjected to an axial load of
10 kN, find the maximum stress induced, taking stress concentration into
асcount.
В
What is the difference between caulking and fullering? Explain with the
help of neat sketches

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The stepped shaft shown in the figure isrequired to transmit 600 kW of power at 400 rpm.The shaft has a full quarter-circular fillet, and thesmaller diameter D1 =100 mm.If the allowable shear stress at the stress concentrationis 100 MPa, at what diameter D2 will thisstress be reached? Is this diameter an upper or alower limit on the value of D2?
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 1m depth.
a shaft 80mm diameter transmits power at maximum shear stress of 63 mpa. find the length of 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 mpa.
A hollow tubular shaft will be used between the engine and the propeller of the boat as shown in the figure. The outer diameter of the shaft is d=74 mm and the wall thickness is t=6 mm. The power of the engine is P=10 kW and its speed is n=694 rpm. Accordingly, calculate the maximum stress on the shaft and show whether it is safe by drawing it to scale within the continuous strength graph given. (Shaft material St37)
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
The propeller shaft of a large ship has anoutside diameter 18 in. and inside diameter 12 in., asshown in the figure. The shaft is rated for a maximumshear stress of 4500 psi.(a) If the shaft is turning at 100 rpm, what is themaximum horsepower that can be transmittedwithout exceeding the allowable stress?(b) If the rotational speed of the shaft is doubledbut the power requirements remain unchanged,what happens to the shear stress in the shaft?